Question Locked

DVI-150's remote not working

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

with my new computer, I got a tv tuner card installed (DVICO DVI-150: FusionHDTV DVB-T Dual Express [Australia / Europe Only] ). now it was all working fine until I had to take my computer back to get a DVD-drive swapped over. since then, the remote for the card has not worked. After contacting the dvico tech support, and getting nearly nowhere, i have almost givin up, and am thinking of buying a new remote.

but first I will see if anyone has any suggestions.

here are the specs of the computer:
Intel i7 920
MSI X58 PRO mobo
6GB RAM
elitegroup Nvidia GeForce 9800GT 1GB
1TB HDD
Vista Ultimate 32-bit
2 screens (ViewSonic VA1912w and Samsung 2333SW)
Logitech MX5500 bluetooth keyboard + mouse

12 replies

by seanferd

Swapped drive- was there a re-installation? Are all the drivers installed?

Anything show up as not working in Device Manager?

Of course I have to ask - are the batteries in the remote good? ;)

edit:
To narrow this down for any future reference, the DVI-150 is this(?): FusionHDTV DVB-T Dual Express [Australia / Europe Only] (?) http://www.fusionhdtv.co.kr/ENG/products/

Arg. This would be a better link.
http://www.fusionhdtv.co.kr/ENG/products/DVBTDualExpress.aspx

This has some interesting bits, if you haven't seen it:
http://www.fusionhdtv.co.kr/eng/Download/SOFTWAREDVBT.aspx

edit: Looking through the manual for the remote itself, it looks like there are plenty of things to go wrong - I'd check all settings.

by .martin.

when i say drive, i mean DVD drive (wasn't opening), so no re-installation.

batteries: brand new, come up as full on my battery tester

as for anything not working in control panel, no, but the remote does not show up (and dvico say that on their site/help file)

but finally yes it is the FusionHDTV DVB-T Dual Express [Australia / Europe Only]

by seanferd

Hmm. Have you tried a different USB port for the receiver?

by seanferd

try plugging a different USB device in it to make sure it is still working.

by .martin.

when I plug my old PS one into the cable it still responds, showing a picture.

by seanferd

and/or software, (you should see two entries in DevMrg under Human Interface Devices)and making sure the remote is enabled in the config, I can only imagine something has failed, like the IR emitter.

What cable are you plugging the PS1 into? I think I misunderstood something, or I was being unclear. Just to make sure: I was wondering if you could unplug the IR receiver (which I understand is connected to a USB port), and then plug a USB device (like a flash drive or mouse) into the USB port previously occupied by the receiver.

by .martin.

as half shown here: http://www.fusionhdtv.co.kr/Eng/Support/FAQInstallation.aspx?act=RD&id=240&pg=0&CATID=10&SCATID=55

the cable on one end has an s-video which plugs into the tuner card. on the other end it has a range of plugs: 3 rca's and an s-video, all inputs. it also has two 3.5mm, a socket and a jack, the jack links back to the line in of the computer, and the IR receiver plugs into the 3.5mm socket.

as for testing it, i would have to find another cable...

as for the device manager, the only thing I could find is : HID-compliant consumer control device

by seanferd

The manual I was originally looking at had the IR receiver on a separate USB plug. I managed to miss that on the page you linked. (Duh.)

I see now where you will only see one of the HID listed.
http://www.fusionhdtv.co.kr/Eng/Support/FAQRemote.aspx?act=RD&id=85&pg=0&CATID=13
If you do the 'test' from the tray icon, does it give any type of error message?

Does everything show up properly for the installed driver checks for you device as listed here?
http://www.fusionhdtv.co.kr/Eng/Support/FAQInstallation.aspx?act=SCAT&CATID=10&SCATID=56

by .martin.

as for the test function, the remote shows up, but none of the buttons respond to the remote

by seanferd

etc., and everything is up to date, I can only imagine that the software/drivers installation is broken somehow (refresh the install & setup), or there is a hardware failure.

Random thought- have you tried disconnecting the new drive? I don't know why it would interfere, but you never know. It's the only thing that is confirmed to have changed.

This discussion is closed to new replies.