Discussion Locked

Freezing at Welcome to Windows popup

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When I boot my pc freezes at the welcome to windows screen where it asks you to enter your user name and password. No error messages. Have rebooted and same problem.

There are a variety of new things going on.

Have just moved the pc from the UK to the US and this is the first time I have attempted to start it. (Have switched the power from 220 to 115)
Hooked up to a new monitor (new to the pc, very old monitor).
Was on a boat for 8 weeks, no idea what it went through.
Few other newcards removed/added before booting.

Have managed to get msgsrv32 not responing when I hit ctrl-alt-del and have to hit that again to get it to reboot.

Any thoughts on how to diagnose??

Many thanks!

10 replies

by thechas

Start with the simple steps.

See if you can boot into safe mode, and select a standard monitor in place of the old monitor.

Reset your CMOS (BIOS) memory, and install a new CMOS backup battery.

While you have the case open, reseat everything.
All plug in cards, all RAM modules, all connectors.

Look for signs of moisture problems. rust, salt

After the above, it's time to go through things step by step.
Back off to a minimal system, (CPU, RAM, video) and see if it will boot.

Then, insert 1 device at a time to find the culprit.

Chas

by ocamper

Not sure what you mean by select a standard monitor in place of the old monitor. I haven't changed any settings, as I wasn't able to access them.

I was able to boot in safe mode (happy to see that my data is there!) In my system properties it says that some drivers are using MS-DOS compatability mode. Further down it lists Drive A and Drive C as using MS-DOS compatibility mode file system.

What exactly is resetting my CMOS memory going to do? (ie, do I need to worry about losing data?most of it is backed up, but I don't really want to reformat the whole darn thing again.)

Thanks!

by ann777

Resetting the memory may help because in shipping, things might have gotten loose. Open the computer and make sure that memory is fully seated in their banks.

WHat OS are you using? Do you know if the computer was preconfigured as far as network info? (msgsrv is usually an error obtained from a networked system). Check and make sure your settings are correct while in safe mode.

Check device manager and see if you have any yellow/red marks on hardware devices. Is the monitor 110/115volts? Do you have any other external devices?

As long as your hdd is booting fine , you should not have a problem with any data loss. It sounds as if something hardware-wise has shaken loose.

by ann777

Resetting CMOS memory will wipe out your hdd configuration in the systemboard BIOS (and all the other configurations specific to your computer... you might want to go to SETUP on your system and write down all the information there if you do decide to pull the CMOS battery). I do not recommend that you do this unless you are also getting date/time errors, or errors from the bios such as "x not found".

by ann777

Your computer freezing at logon seems a little strange.

Can you log on as Administrator? This whole thing might be a networking issue/computer OS issue or software configuration issue.

by thechas

Windows may be hanging because your monitor is different than the monitor that you used to have, and it is having problems dealing with the differences.

In safe mode, right click on a blank area of the desktop (no icons)
Select properties.
Click on the settings tab.
Click on the advanced button.
Click on the monitor tab or button.
Click on show all devices.
Either select the mfg and model of the monitor you are using, or select tha nearest match from standard monitor types.
Click on Okay and apply to exit display settings.

As to the CMOS battery and settings.
It is possible that the long period of time without power applied to the PC ran down the CMOS battery.
When this happens, the BIOS settings stored in the CMOS memory sometimes get corrupted.
The best way to eliminate this as a problem, is to replace the battery, and follow the reset proceedure for your system.
(Usually setting a jumper, turning on the system, turn off the system, reset the jumper, restart the system)
Then, enter Setup when you restart the system, and adjust the BIOS settings as needed.
Date and time,
Drives (floppy, Hard drive and CD-ROM)
Ports (USB, COMM, you usually need to set the parallel port to EPP/ECP mode)

There are a couple of articles in the archives at Tech Republic on adjusting your BIOS settings.
Just search the articles on bios

To get rid of MS-DOS compatability mode, one way is to re-install the IDE bus driver for the chipset on the motherboard.

Alternately,sometimes it works to just delete all drive controllers from device manager, and allow Windows to re-install them when you re-boot.

Chas

by ocamper

Not sure what solved the problem in the end, fiddled with a few things in safe mode, removed all pci cards, reseated everything left and slowly put it all back together. Working fine.

Thanks!

This discussion is closed to new replies.