Question Locked

How to install Hard drive into laptop

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I just bought a laptop with Vista. Not wanting to remove Vista, ['Just in case'] I purchased a SATA Hard drive to replace the original. I now find that no version of windows 'sees' it. Can anyone advise on how to install windows into a SATA hard drive on a laptop.

12 replies

by cdelatorre

Hi,
first of all, I've been reading techrepublic for sometime now but its just this time that i manged to register. anyway, i hope this helps

1) as any other hard drive, you need to insert it to the laptop. Models like the Dell D620 or HP N6000C has their drives at the side. Its easy just look for the "disc" sign at the back
2) once you plug it in, go to BIOS [other accept F2 - some F10 or F11]. Check if your sata hardrive is detected by the firmware.
3) Install a Windows Operating System cd
4) It should ask you to press any key to start the OS installation.
[pre-requisite] - you must set the boot option to CD by pressing [F8] after the first few seconds you press the power button
5) Installing an Operating System is intuitive. Just let it load all the drivers until you can see a NEXT button that you can press.
6) Configurations such as Time zone, computer name, accounts is very easy.

Let me know how you make out!

by bbwalters

Hi cdelatorre, Have been working on computers for 20 years but this one has got me stumped.
The WINXP loads all the files for installation to the new HD, then at the end, where asks what you need to do. Like press to install, it comes up 'Hard Drive not seen'
I am at the moment installing an image created from the original HD after using 'Paragon'

by magic alex

Are you able to plug the hard drive into another laptop and verify that it's not damaged?

by mwhipple

First ensure that the computer sees the hard drive. You should be able to chek the drive through either the computer BIOS or the SATA controller BIOS. You may also want to try booting Knoppix or a similar LiveCD which has many drivers built in to ensure that the problem is in fact Windows and not hardware or lower level software.
I came upon a similar issue not that long ago with a laptop which supported a dual SATA/RAID hard drive configuration. If this is the case there may be separate drivers for the 2 modes, so ensure that you download the proper driver and load it during the Windows install (either using the F6 option...or it seems to automatically check floppy drives).

by dumphrey

is recognizing the hard drive. Then see if there are any settings for the drive you can change to get it to read. If the bios does not see the disk, its probably a bad drive.

by older mycroft

If you haven't installed the SATA drivers, Windows XP cannot see the drive.

by older mycroft

Actually - XP did find the harddrive because at the time of install, the install disc had formatted it. XP then proceeded to install from the optical disc but could not see itself when booting to itself.

In the first few seconds of the install, there is a blip during which you can elect to install SATA drivers.

Unfortunately XP cannot install SATA drivers from an optical disc like Vista can, so you require a USB floppy for the task. [I have heard of some success loading the SATA drivers from a USB memory stick but have no first-hand experience of this]

I am assuming that he went into this little endeavour without fully researching what would be required.

The question as to whether this laptop can be fully serviced by working XP system drivers has yet to be addressed. Unfortunately the Upgrade Advisor for the transition from XP to Vista never had a counterpart to advise on the transition from Vista to XP.

by magic alex

ahh yes, your absolutely right, sorry for the misconception

by dumphrey

have addressed this by making the sata disk appear to be an ide disk to windows (i would guess). On my desktop I installed XP Sp1 with no extra drivers straight to the sata disk with no issues, where as the sata dives on the mobo previous to this did require drivers to be included during the install.

by bbwalters

Western Digital WD1200BEVS 120GB 2.5" SATA Hard
Drive
This is an ?OEM? hard drive. What you get is just the drive in a safety screening bag.
My laptop was installed with Win. Vista. Not happy with this I decided to retain the original as it was, and replace the laptop with a new HD. When received the drive is not partitioned or formatted. Trying to install Windows XP was fruitless. ?Drive not recognised? kept coming up all the time.

The answer is to go to the Western Digital web site and down load their Hard drive software for the WD Scorpio 120 GB SATA Hard Drive WD1200BEVS Data Lifeguard Tools 11.2 for DOS (CD) [DLG_V11_2.zip] t: http://www.westerndigital.com/en/products
This zip file contains a bootable CD image of the Data Lifeguard v11.2 installation CD which contains both DOS and Windows versions and was written specifically for the installation of Western Digital EIDE hard drives.
If your computer system already has a hard drive installed with an operating system of Windows 98SE or greater, you should use the Windows version of Data Lifeguard for best results.
The DOS version is required if installing a hard drive into a new system not partitioned or formatted and without existing operating system support.
If you plan on copying the contents of a boot drive, Western Digital recommends using the DOS version of Data Lifeguard Tools.
Since the using the Lifeguard tools and installing WIN XP it has been faultless. Incidentally the software specification mentions ?Suitable for EIDE.? I found it worked with the SATA drive.

This discussion is closed to new replies.