Question Locked

How to Install Windows XP that don?t have SP2 onto a New Hard Drive (320GB)

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a new hard drive and I can?t install using windows xp cd which does not have service pack 2 on to it. What can I do?

5 replies

by wcrespo95

If it is a new Hard Drive, put a Windows XP CD into the CDRom Drive and reboot the PC, you want the PC to boot off the CD, you should then get an option to boot from CD. then continue the installation, it is very simple. If the CD is not WinXP SP2 you can download SP2 from www.microsoft.com, you will be asked to validate your copy of XP so make sure you have a valid key when installing the OS.

by rob miners

Windows XP does not support 48-bit LBA support unless you are running Windows XP SP1. If you want to use 48-bit LBA support, you must apply Windows XP SP1 or later and this will increase the capacity of your hard disk to more than the current 137 gigabyte (GB) limit.

You may have to Slipstream the Sata Drivers for your Motherboard if you don't have access to a floppy drive. You can also use this method to Slipstream SP2 or SP3. You will also have to know the Make and Model of your Motherboard to get the right Sata drivers.

http://www.maximumpc.com/article/howtos/how_to_slipstream_windows_xp_sp3_and_vista_sp1

Integration of the Intel SATA AHCI or SATA RAID drivers by using nLite

http://www.msfn.org/board/Integration-of-Intel-Sata-and-Raid-drive-t107504.html

Extract and Copy the SATA Drivers to a Floppy Disk. Boot from the XP CD and when prompted, press F6 to install the SATA drivers from the floppy disk. If you haven't a Floppy Drive Slipstream your XP installation with the SATA drivers.

How To: Slipstream your XP installation

Download nLite

http://home.midmaine.com/~nlite/nlite/nLite-1.4.8.installer.exe

These are the steps that I took

Download the Sata Drivers from the manufacturers web site.

Installed Nlite

Extracted Sata Drivers to a folder named Sata

Copied the entire XP CD to a folder named XPS

Ran Nlite and Browsed to the XPS folder, Next, next then selected Drivers and Bootable ISO click next

At the Drivers Tab click insert, single driver and navigate to the folder with the inf for windows XP.

Highlight it and select open and select next. Select Textmode driver and select the XP Sata driver and click OK.

Click next and Yes to apply changes, next and select Make ISO. Use Nero or similar to burn it to a CD.

Magic Disk can be used to load the .iso to copy the information back to the hard drive to do the second install of either the Sata Drivers or the Service pack.

http://www.magiciso.com/tutorials/miso-magicdisc-overview.htm

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by oh smeg

You can install XP to this HDD but it will only be of a 137 GIG Capacity.

You can then enter Drive Management and configure a second partition for the rest of the HDD after loading SP2.

Or if you want to use all of this HDD as 1 partition you can load XP install SP2 and then use GParted to expand the partition out to the full capacity of the drive.

http://gparted.sourceforge.net/download.php

Personally though I would slipstream SP2 to a Install CD made with nLite as suggested above. nLite does have a set of instructions listed on their Web Site here if you didn't fully understand the above description

http://www.nliteos.com/guide/

Col

This discussion is closed to new replies.