Question Locked

How to properly replace a motherboard on server with RAID array?

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm at a site where we have a Dell 1400 poweredge server with a raid array that will not post, even though I see lights on the motherboard and the raid array spins up. I am informed by Dell support that it is either the motherboard or the processor. I have obtained both parts. Since the system is so old, they are not the original parts but the latest supported version of the parts.

The worst part of this, is the data is NOT backed up. Our backup system failed a few weeks before and is also on my desk. We had a lightning storm a few weeks ago which seems to be the culprit, as my UPS is also blown.

While I am very confident replacing these items in a desktop unit, the RAID array intimidates me. I do not know whether I can simply install the new motherboard and processor, connect everything back up, and move on like nothing happened. Or if the RAID controller is going to make things unsafe for the data in the RAID array.

Any advice here will be welcome. I am loathe to rely only on Dell's support. I need more opinions. Thank you!

6 replies

by lynchcj

Is this the same Heather that worked at P&G?

I can pull some instructions from Dell's support site as I am warranty parts certified. I will see if i can find what you need?

Chris Lynch

by lynchcj

I set my preferences so you can now message me I guess by default they are turned off

by liame

If its raid 0 or 5 and the raid controller is on a seperate card (ie not built into the motherboard) and the controller has not been damaged you should be okay to move the raid setup as is to a new box. Be carefull to label the drives and their connections before anything gets unplugged though. Boot on a different drive and see if the raid is visible... if it is back it up!

Alternatively... if its a raid 1 you are laughing. Either of the disks will make a new basis for a mirror... unless its not hardware raid in which case only the primary is bootable. I have had a Dell system with software raid 1 have the primary disk fail and would not appear to post properly.

What controller card are you using? If its a perc its most likey harware raid, something like an adaptec 39160 and its software.

by lynchcj

SYSTEM BOARD
The following procedure outlines the steps for removing and replacing the system board.
Removing and Replacing the System Board
1. Before removing the system board:
? Disconnect the AC power cable from the back of the system.
? Open the cover.
? Disconnect all cables from the system board.
? Remove the processor shroud.
? Remove the VRM.
? Remove the processor.
? Remove the memory.
? Remove the Video card.
? Remove any other PCI cards.
2. Remove one screw from the front of the system board.

3. Lift the two green tabs at the front of the system board.

4. Slide the system board toward the front of the system, and then lift it out of the chassis.

5. Reverse the previous steps to replace the system board.

BEEP CODES
The initial POST sequence may not have a any video displayed and a pattern of beep codes may be heard. For example, one beep, followed by a second beep, and then a burst of three beeps (code 1-1-3) indicates that the computer was unable to read the data in non-volatile random-access memory (NVRAM).
If the system loses power and beeps constantly when you turn it back on, the BIOS is probably corrupted.
Beep
Code Description Beep
Code Description
1-1-2 CPU register test in progress 2-4-3 1st 64K RAM chip or data line failure - bit E
1-1-3 CMOS read/write test in progress or failure 2-4-4 1st 64K RAM chip or data line failure - bit F
1-1-4 BIOS ROM checksum in progress or failure 3-1-1 Slave DMA register test in progress or failure
1-2-1 Timer Test in progress or failure 3-1-2 Master DMA register test in progress or failure
1-2-2 DMA initialization in progress or failure 3-1-3 Master IMR test in progress or failure
1-2-3 DMA page register read/write test in progress or failure 3-1-4 Slave IMR test in progress or failure
1-3-1 RAM refresh verification in progress or failure 3-2-2 Interrupt vector loading in progress
1-3-2 1st 64K RAM test in progress or failure 3-2-4 Keyboard controller test in progress or failure
1-3-3 1st 64K RAM chip or data line failure (multi bit) 3-3-1 CMOS power fail and checksum test in progress
1-3-4 1st 64K RAM odd/even logic failure 3-3-2 CMOS Config info validation in progress
1-4-1 1st 64K RAM address line failure 3-3-3 RTC/Keyboard controller not found
1-4-2 1st 64K RAM parity test in progress or failure 3-3-4 Screen memory test in progress or failure
1-4-3 Fail-safe timer test in progress 3-4-1 Screen initialization test in progress or failure
1-4-4 Software NMI port test in progress 3-4-2 Screen retrace tests test in progress or failure
2-1-1 1st 64K RAM chip or data line failure - bit 0 3-4-3 Search for video ROM in progress
2-1-2 1st 64K RAM chip or data line failure - bit 1 4-2-1 Timer tick interrupt test in progress or failure
2-1-3 1st 64K RAM chip or data line failure - bit 2 4-2-2 Shutdown test in progress or failure
2-1-4 1st 64K RAM chip or data line failure - bit 3 4-2-3 Gate A20 failure
2-2-1 1st 64K RAM chip or data line failure - bit 4 4-2-4 Unexpected interrupt in Protected Mode
2-2-2 1st 64K RAM chip or data line failure - bit 5 4-3-1 RAM test in progress or failure above address 0FFFFh
2-2-3 1st 64K RAM chip or data line failure - bit 6 4-3-2 No memory in Bank 0
2-2-4 1st 64K RAM chip or data line failure - bit 7 4-3-3 Interval Timer Channel 2 test in progress or failure
2-3-1 1st 64K RAM chip or data line failure - bit 8 4-3-4 Time-Of-Day Clock test in progress or failure
2-3-2 1st 64K RAM chip or data line failure - bit 9 4-4-1 Super I/O chip failure
2-3-3 1st 64K RAM chip or data line failure - bit A
2-3-4 1st 64K RAM chip or data line failure - bit B
2-4-1 1st 64K RAM chip or data line failure - bit C
2-4-2 1st 64K RAM chip or data line failure - bit D

by heather_s_it

Hi Chris! Long time since I've heard from you! Thank you for you information!

I have resolved this issue on my own, however, would love to catch up with you. Send me email at my

firstname.lastname@na.manpower.com

This discussion is closed to new replies.