Question Locked

how to wipe clean (format) an external HDD

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Hi I bought a used 2.5" HDD and installed it inside an external enclsure. I want to wipe the drive clean and use it to transfer files between computers. When I plug the drive into my desktop USB port, the desktop says - as normal - new hardware found. While it sees the external enclosure controller, I can't see the actual ext. HDD in Explorer, My Computer, or anywhere. I checked Hardware Profile using Control Panel and the enclosure controller was there and there was no conflicts indicated. I believe the HDD was a primary drive in a dead corporate Compaq notebook before, and still has Windows XP Pro installed on it. Being a corporate notebook it must have a Windows start password feature requiring a password to start Windows. Is that what's causing my desktop to not "see" the actual drive even though it recognizes that a new hardware has been connected? But my desktop doesn't have USB boot enabled? Also I have tried it in three other desktops that I have and ran into the same problem. So the problem is definitely not caused by the desktop. How do I get my desktop to "see" this external HDD so I can use Command Prompt/Format or Windows Disk Manament to wipe it clean? I don't need to save anything from this HDD. Thanks.

22 replies

by skdtech

the jumper settings. The enclosure may require a specific setting such as slave for the installed drive. Also if the enclosure had a two plug cable try plugging in the second usb connector as well to make sure it is receiving sufficient power to operate.

by petershum

The enclosure is a very simpleone. It has only a connector that I plug in the IDE drive. I then insert the drive into the case and fasten a couple of screws to keep it inside. There are no jumpers or switches that I could see.

by oh smeg

If you look at where you plug the HDD into the enclosure you will find that there are 6 Pins unused here.

These are the pins that the Jumper may be on depending on the Make of the HDD. In these external enclosures the requirements are different depending on the enclosure and the HDD make. Some require the HDD to be set to Master and some require the Jumper to be removed for the HDD to be readable.

If there is a jumper on this HDD make sure that it is set to Master not Cable Select CS and try again. If it can not be read then remove the jumper. If it doesn't have a jumper on the Drive fit one so it is set to Master and see if it is readable now.

Also because this came from a corporate environment it may have been wiped previously so without any Partition on the Drive you will need to format it by opening the Drive Management scrolling down to locate the HDD and then right clicking on it and selecting Format. Then Format the drive as required and that should be all that is required.

Col

by older mycroft

Isn't the best of starts for a 'new' HDD. Perhaps the HDD was the main cause of the death.

Also, being that it came from a corporate laptop it may have been encrypted.

As regards [i]"I can't see the actual ext. HDD in Explorer, My Computer, or anywhere"[/i] ~ does 'anywhere' include Disk Management ?

What legend is visible when you invoke Safe Removal ?

by petershum

Yes I tried Disk Management and it does not see the drive. I was told the HDD was working previously and I had dealt with the chap before with no bad experience. When I clicked on the little USB icon to eject it, nothing happens for a long time and then a message pops up and said the device cannot be removed now. If I wait longer and then try again, it would let me remove the drive.

by older mycroft

Are you aware that with those little 2.5" aluminium enclosures with the two side screws - you can fit the drive to the IDE connector and assemble it with the HDD [b]UPSIDE DOWN !![/b]

I know it's possible - I've once done it myself. When it's upside down the system won't see it. Have a look-see. When it's upside down, the IDE connector is OFF to one side by one connection.

ALSO - they don't like being connected with a USB extension lead - that will result in the drive not being seen also.

by petershum

Yes I have made sure that the connector went on correctly. The connector fits flush on both edges with the HDD. I have noticed that it only goes on one way without being offset. Also if it is offset it wouldn't have fit inside the enclosure. Also I use the cable that came with the enclosure and did not use any extensions.

by older mycroft

If possible, try a different enclosure (the interface board in these units IS kinda flimsy and can fail).

I assume you've tried different USB ports too.

Someone else's ideas will probably see you right.

by petershum

I don't believe it is the enclosure because the 4 desktops I tried all detected the interface board. And yes I have also tried different ports on top of the 4 desktops. I really think that it is because my desktops tried to read the drive but ran into the encryption, so it hangs.

I feel strongly to find a degausser (or some strong magnet) and de-magnetize the stupid drive. That ought to "kill" the encryption!

Thanks for trying to help. It is much appreciated. As you said someone might have run into the same problem before and have just the fix.

by seanferd

if you use a degausser on the drive.

It isn't the contents of the drive that cause it not to be recognized, it is a hardware problem.

by rob miners

to the person that you bought it from and ask them to Partition the drive for you. If all goes well you will have a working drive. If they have problems you can sort out an exchange or a refund.

Keep us informed as to your progress if you require further assistance.


If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D :-bd

by petershum

The chap doesn't have the resources or knowledge (what little I know of computers is still much more than he does, LOL) to partition it for me. Also he is sort of a friend so for what I paid (not much)for the used drive, I don't think I'll ask him for a refund (he can't exchange because he doesn't have another one) because that may give him the wrong impression that I thought he "screwed" me. Again for what I paid for the drive, this is more of a "challenge" than a money issue.

by lnxguy

And put it directly into another laptop. If the drive is not recognized, it is bad. If it is recognized, partition and format it. Then it should work in the enclosure.

I use a cheap tool that works great for jobs like this; it is a USB connector that attaches directly to any ATAPI or SATA drive. It always works.

by petershum

Other than the desktops I don't have a laptop but a netbook (Acer Aspire One), and I can't (don't believe I can anyway?) plug the drive into the netbook.

Your suggestion for using a "tool" to connect the 2.5 drive to an IDE connector on a desktop is an interesting idea, and I'll see if I can (i.e. find an adaptor) try it.

Thanks.

by oh smeg

These need to be plugged onto the 2.5 inch drive correctly if you plug them on the wrong way the 5 Volt DC will be feed directly into the IDE Controller on the M'Board and destroy that integrated Circuit.

http://www.mittoni.com.au/25-to-35-ide-hard-drive-hdd-adapter-p-1296.html

Look very carefully at the adapter before applying any power and with every one of these that I have used previously the Power Leads need to be beside the Pins that set the Drive to Master, Slave or CS but do not just believe that they should be that way look and make certain before you apply any power. If there are any directions make sure that you read and understand them before doing anything else here.

I didn't think that it was possible to mess up with these as they seemed fairly fool proof to me but one customer bought one from me and blew up their M'Board.

Col

by petershum

The drive was a Master in the previous notebook so I'd presume the jumpers (if there are any) would have been set as such. Also I didn't notice (although I didn't check closely) any jumpers on the drive. I'll take it out of the enclosure again and check to see if there are any jumpers.

I understand this drive hasn't been wiped clean but if it has, then it would be no different from a brand new blank drive and wouldn't Disk Management have seen it? It doesn't now though.

by petershum

I took the drive out of the enclosure again and took a closer look. There are about 4 jumper pins with a jumper link! They are smaller than those on a 3.5" drive and this is the first time I played with 2.5" HDD's and didn't realize they also have Master and Slave setttings. Hmm can one put more than one HDD's inside a notebook? I never thought that was possible. Anyways I removed the jumper link, put it back inside the enclosre and voila my desktop sees it! I guess the jumper link must have been to set the drive as Master and with it there my desktops hanged previously becasue the drive wanted/tried to run as Master, and since my C drive is the Master, there can't be two Masters right? Hahaha!

I started Disk Management and initiated reformat on the 2.5" HDD. I am now waiting for the formatting to finish (it is at about 60%).

Thanks to each and everyone who have so kindly helped and offered their advice. It is much appreciated.

by oh smeg

The Electronics inside the enclosure need it that way to work. Some need a Jumper on and others need the jumper off just the way that it works.

As to fitting more than 1 HD inside a NB yes you can with some NB's but only with the High End ones. Now Days you can have a Working RAID Array inside a NB if you wish with the more Budget ones that are available though these are all SATA Drives now. The Older NB's had what was effectively 1 IDE Chanel in them and the HDD was set to Master and the Optical Drive was the slave. That was the more common setup.

Col

by oh smeg

This is Dependant on Hardware and the way that it works. If the Old NB that it was in didn't require a Jumper and this enclosure does you need to fit a jumper that is all there is to it.

On the other had if the old NB required a Jumper and there is one on it and the enclosure doesn't require a jumper you need to remove the jumper for it to work with that enclosure.

And in answer to your question Yes if it was wiped Disc Management should see it but only if the Enclosure has the Drive correctly set and the right USB Plug Plugged into the Computer.

Some of these external HDD Enclosures have a Y Cable where there are 2 USB A Plugs that are plugged into the Computer. The one furriest from the Enclosure is a Power Plug Only and has no data going through it so if you have 2 USB A Plugs on the cable you need to plug in either both if the drive is larger than 80 GIG or the Middle one if you are connecting to either a Powered USB Hub or a Desktop computer.

Regardless of the size of the HDD if you are plugging it into a NB you should use both Plugs in USB Sockets that are part of the M'Board. If you plug them into something like a PCMCIA USB Card the drive will not work. Also if the Enclosure has a power point and you intend to use this with modern NB's a lot you should invest in the Power Adapter and use it to prevent damage to the HDD inside the enclosure from being plugged into Low Powered NB USB Ports.No matter what though the Computer should see a Mass Storage Device when you plug in the Data Plug of the Enclosure to a computer. Even without a HDD attached the Computer should recognize the USB to IDE interface card in the enclosure.

Just a word of explanation every new IDE NB Drive that I have bought for the last 5 or so years comes with a Jumper on the outside of the Anti Static Bag that you can use if the hardware requires it. The HDD makers do not fit these to the HDD as they may not be necessary and cause more problems by fitting them than by not fitting them.

Col

by petershum

You are absolutely correct and that was exactly the problem. I removed the jumper and it is now being reformatted.

Thanks very much again for a great and informative advice mate.

This discussion is closed to new replies.