Question Locked

IBM Netfinity 6000R and SCSI Problems

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently bought an used Netfinity 6000R (8682-1RY) server. It came with an Adaptec AIC-7899 SCSI Controller and an IBM ServeRaid Controller.

When I first started the machine up, it seemed that the included SCSI Drive (IBM Ultrastar DDYS-T36950 LVM) was faulty because it did neither work on the Adaptec or ServeRaid controller. I tried different jumper settings (namely FORCE SE) to make sure it isn't a configuration issue, but the drive always timed out.

I then ordered two IBM DRHS-36D drives, but they did show similar symptoms. The Power LED on the Drive Backplane shortly lights up. When I attached one of the two DRHS-36D drives to the adaptec controller, I could remove the drive when the controller's scan did hang and access the Adaptec's BIOS, and even do a block test so I don't believe that the drives are faulty at all. Sometimes the drives spin up, sometimes they don't, and when I removed the drive during the Adapter's scan (before entering the SCSIselect utility with Ctrl+A), it did spin up correctly when doing the block test in SCSIselect.

I think that either both cables are defective, or that the HDD Backplane is faulty. As I do have no knowledge about IBM's technology and as I don't have any other hardware to test this on, I wonder what I should do next.

I read alot of stuff regarding LVM, and some people say that the end of the SCSI chain must be terminated - but I guess this was done by IBM on the HDD backplanes. Another post was saying that some PSU are unable to power the drives (the original drive has 750mA at 5V, 1100mA at 12V and the replacement drives have both 1.10A at 5V and 1.15A at 12V).

regards,
Timo

9 replies

by Former member

Try and get another one to test out.

Please post back if you have any more problems or questions.

by timo.hummel

The Netfinity 6000R has redundant power supplies. I usually operate the box using all three PSUs, I doubt that all three are defective.

by Former member

Will they be able to give what you need?.
The power supplies are nice but a bit useless if the are they do not have the extra wattage/power to get the server up and running.

Please post back if you have any more problems or questions.

by timo.hummel

We are not talking about a custom server. This is a Netfinity Server, and the PSUs are original, thus there's absolutely no way that they are underpowered.

each PSU has 263 watts, 14.0A at +12V, 19.0A at +5V, 20.0A at +3V.

by oh smeg

The Netfinity Series of Servers have both a SCSI and RAID Controller built in. For SCSI Drives you need to set them to different addresses that is number 1 to 7 or 0 to 14 depending on the SCSI Type that you have,. The 2 or 3 Drives [b]Can Not[/b] have the same SCSI address or they will not work

Now as to the issue of the drives not appearing this isn't a problem you need to set the drives and then start to install your OS. Depending on what you want to install you will need to install either the SCSI or RAID Driver so press the [b]F6 Key[/b] when the first blue screen appears in the Windows Installer and push the key when it appears not 5 seconds or more latter. You will then after the computer has loaded the Windows Installer into RAM be prompted to Insert the SCSI or RAID driver on a floppy in the A Drive and told to press enter when you have done this. You need to copy the Driver that you are using to the Root of a Floppy that is not in a Folder or Windows will be unable to install it.

If you don't have a floppy available you can Slipstream the Windows OS to a Install Disc with the Required Driver by using nLite on some Window Server products and all versions of XP.

http://tinyurl.com/e2mo4

Read the instructions on the NLite Web Site to see if your desired Version of Windows is supported if it is read the Instructions on how to use nLite and make your Slipstreamed Install Disc. You can at this stage also add any Service Packs that you want to as well. With Windows Service Packs you only need to include the last one made available because they include the bits from previous Service Packs. So if you are attempting to install W 2000 Server you only need to apply SP4 not 1, 2 & 3 if SP4 is the last one made available. It's been a long time since I've looked at 2000 so there may be a SP5 available.

If you are wanting to install a different OS you will need to do the same thing that is add the SCSI or RAID Driver and to do this you'll have to consult the OS Makers Directions.

Col

by timo.hummel

First, you do not need to set SCSI Id's on LVM devices. This is done by the HDD backplane.

Second, if the SCSI adaptor doesn't recognize the drives, there's no way an OS would.

Not helpful at all.

by oh smeg

The same model and it's different I don't think so. :D

Actually how are you sure that the Adapter isn't seeing the drives? If they are not addressed it can't and while the Circuit Board can allocate different Addresses per Socket that doesn't mean that the Primary Addressing doesn't need applying.

But feel free to take advice from people who don't know the hardware in the first place.

Col

by Former member

It seams everything is ok except this backplane that you have a issue with.

Please post back if you have any more problems or questions.

This discussion is closed to new replies.