Question Locked

Installing, Configuring 1 SATA HD and 2 DVD-RW drives

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm working on only my third PC build and have run into a snag. On an
Asus Motherboard I am trying to install a SATA HD and two DVD-RW
drives. I'm trying to install the DVD-RW drives on a single IDE ribbon
cable. When booting the PC the system recongizes the presence of the
two DVD drives, but they do not appear once entering the BIOS. I don't
know if I have the Master/Slave configuration with the DVD drives
confused, or if there is some kind of conflict with the SATA HD, the
truth is I'm in the dark right now on this one. Any info would be great.
If more detail is needed I'll be happy to provide it. I'm just looking for
any suggestion on what I could go about doing in terms of installation
and configuration. Thanks. (P.S. - be kind to the newbie)

8 replies

by hal 9000

And the other to Slave there is no problem as BIOS doesn't see Optical Drives. If you turn off the splash Screen you should see the Optical Drives when you initially boot the system after the Memory Test.

There is nothing at all wrong here with what you are seeing.

Col

by jameson131

I will continue to forge ahead then. Thank you for the quick
response...I may be back to pick your brain a bit more if I run
into another snag, if that's okay. Thanks again.

by hal 9000

Just a not here depending on the Chip Set on the M'Board you are using you may need the SATA Drivers copied to the root of a floppy so you can install them. If you have an Intel Chip Set M'Board you'll most likely need this, however if you are using a NVidia Chip Set M'Board you'll probably not need to do this.

The other Chip Sets is anyones guess.

Col

by jameson131

I seemed to have run into another snag here. The problems
is that there is a screen that pops up for a split second
recognizing and naming (brand, serial) the two dvd drives
that are present, but they do not show up in the CMOS as IDE
drives, regardless of being configured properly. The SATA
drive is recognized, but that is it. From here I am stuck
because I obviously can't boot from a CD/DVD without an
optical drive. Any suggestions?

by hal 9000

On them. There is a small plastic bit that covers some metal that shorts out 2 pins beside the IDE Cable away from the Power Lead side of the Drive.

What you need to do is set one to Master and one to Slave. Depending on the make of drive most are set to master and you can not have 2 Master Drives on the 1 IDE Channel. If in doubt disconnect one of the drives and try booting from the other connected drive.

Col

by jameson131

I understand the nature of setting one device as master and the other as slave on an IDE ribbon cable, but I've run into a weird situation. When I set the second DVD drive (slave) jumper to slave, the boot menu doesn't recognize the drive, nor is it available when in WinXP, yet when I set both DVD drives on the IDE to Master, the PC recognizes both drives and are fully fuctional, regardless of the fact that the ASUS boot menu states that the slave is "not compatible". Both drives are fully fuctional after the initial boot and are recognized by XP and are fully functional, yet at the same time for the sake of being thorough and learning how to properly build a PC, I'd like it much more if there wasn't that error message upon booting, regardless of functionality. Any Info would be greatly appreciated. Thanks again.

by hal 9000

That setup shouldn't work at all. If you where using CS [i]Cable Select.[/i] Yes I could understand why it is so but most defiantly not with both drives set to Master.

There is only one possibility and that is the M'Board Chip Set overrides the Optical Drive settings and allocates what it wants to depending on the location of an IDE Drive on the IDE Data Lead. There was some talk of doing this quite a while ago but I've never heard anything come of it yet though that could be one of the advantages of that M'Board Chip Set. Supposedly this was to make assembling computers easier as it would be a completely Jumperless setup procedure.

Sorry but there is nothing else that makes any sense.

Col

This discussion is closed to new replies.