Question Locked

Intel splash screen hangs for 3 minutes

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When booting up the intel splash screen suddenly starting hanging for at least 3 minutes. There were no hardware changes or bios updates. Quick boot is enabled and there is no option for silent boot. My system info is: OS Name Microsoft Windows XP Professional
Version 5.1.2600 Service Pack 3 Build 2600
OS Manufacturer Microsoft Corporation
System Name DAMIAN-1
System Manufacturer alienware
System Model alienware
System Type X86-based PC
Processor x86 Family 15 Model 2 Stepping 4 GenuineIntel ~1994 Mhz
BIOS Version/Date Intel Corp. MV85010A.86A.0011.P05.0111141737, 11/14/2001
SMBIOS Version 2.3
Windows Directory C:\WINDOWS
System Directory C:\WINDOWS\system32
Boot Device \Device\HarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "5.1.2600.5512 (xpsp.080413-2111)"
User Name DAMIAN-1\Damian
Time Zone Eastern Daylight Time
Total Physical Memory 1,024.00 MB
Available Physical Memory 608.10 MB
Total Virtual Memory 2.00 GB
Available Virtual Memory 1.96 GB
Page File Space 2.41 GB
Page File C:\pagefile.sys

5 replies

by thumbsup2

Turn off the quick boot which eliminates the intel screen so you can see what is happening at boot time. Sounds as if something is waiting for a response but it's eventually timing out. Either that, or sizing RAM is taking an unusually long time.

by merlyn1952

Thank you for your response to my query. All that happens when I turn the quick boot off is I get a rapidly blinking cursor in the upper left corner for about 3 minutes then on to the boot sequence. Again, any input would be greatly appreciated.

by rob miners

Update all of the Motherboard Device drivers. EG: Chipset, Video and Lan.

You can add /BOOTLOG to the Boot.ini file and watch the screen and hopefully see where it pauses.

It also causes Windows to write a log of the boot to the file %SystemRoot%\Ntbtlog.txt.

Press the WinKey + Pause/Break, Advanced System Settings, Startup and Recovery, Settings.

When you are in here you can select Edit to open your Boot.ini. It should look like this if you aren't dual booting.
You will need to add this to the boot.ini file /NoExecute=AlwaysOff

eXample:
Standard
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Windows XP Professional" /fastdetect

Modified
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Windows XP Professional" /fastdetect /BOOTLOG

Click Start, Run type msconfig and press Enter.

Now if you have the Configuration Utility open.
Configure selective startup options
In the System Configuration Utility dialog box, click the General tab, and then click Selective Startup.
Click to clear the Process SYSTEM.INI File check box.
Click to clear the Process WIN.INI File check box.
Click to clear the Load Startup Items check box. Verify that Load System Services and Use Original BOOT.INI are checked.
Click the Services tab.
Click to select the Hide All Microsoft Services check box.
Click Disable All, and then click OK.
When you are prompted, save the settings and restart the System.

If it is working in Normal mode re-enable one item at a time until you find out what is causing the problems.
When you have it sorted out re-run the Configuration Utility and in the System Configuration Utility dialog box, click the General tab, and then click Normal Startup.

Let us know how you get on.

by oh smeg

It is a BIOS problem.

So if you are absolutely sure that nothing has changed open the case and replace the BIOS Battery on Intel M'Boards this should be a CR2032 Type Battery.

Just make sure to remove the Power Lead from the case before you pull the battery as if you drop it onto the M'Board it will cause a Short Circuit and destroy at the very least part of the M'Board.

When you replace the Battery plug the system back into the Mains and turn on. Press the Delete Key and enter the BIOS set the Date and Time and then chose the Performance Options and this should cure your problem. ;)

Col

This discussion is closed to new replies.