Question Locked

IP Address

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have 5 computers in my home connected by a wireless router through a cable modem. I cannot connect two computers to my office getting an error message "another computer is logged on with your IP Address". How can I get around this? Can I bounce off another server somewhere to change the IP or what without having to buy additional equipment. Anything?

22 replies

by older mycroft

The same thing happens if you try to play a 2-player online game, on two computers, through the same modem.

Either the first computer holds the link, denying access for the second computer OR the second computer steals the link from the first computer.

ALL your computers are entering the outside world with the same IP address.

by nimmo

That's why NAT and PAT were invented, to conserve public IP addresses and allow multiple devices to use a single Public IP address by translating the inside IP to a public IP whilst keeping track of connections via ports.

by keyscapt

I understand why this is happening and the reason behind it. I just need to know a work-a-roung.

by Former member

A switch box, connect your computers to the switch and then have the switch connected to the router. Here is an example:

http://www.netgear.com/Products.aspx?for=All

Please post back if you have anymore problems or questions.

by keyscapt

Thanks for the suggestion. This NETGEAR?s FS100 series desktop switch would be a good choice? Would I connect computer to cable modem, modem to switch and swith to router? This switch would correct the issue?

by nimmo

Why not release and renew the connection on the PC that is having the conflict.

by dev_santana

Nimmo >Agreed
Launch cmd
type > ipconfig release than
type > ipconfig renew

by keyscapt

If I release and renew I'm still going to get the same IP Address provided to me by my ISP since my wireless router only supports one IP.

by keyscapt

when I try to release ip -

cmd
ipconfig /release

I get message that it requires elevation. What does this mean and how do I Elevate.
Thanks

by nimmo

Ok I think you are misunderstanding something, your single IP address provided by your ISP is a public IP this allows all your LAN PC's to access the net via your router that holds the connection details.

Your Private addresses is either provided by a DHCP server on your LAN or is statically set.

When you use the command ipconfig /release then ipconfig /renew it is releasing and renewing the Private IP address of the PC not your external IP address.

As for requiring elevated privledges do a right click on the cmd executable )located in windows\system32\cmd.exe) and select run as administrator then do a release and renew.

by keyscapt

Trying to eliminate the duplicate IP Address found while connecting to my remote server at my office. I get an error message stating only one user with this IP address is allowed to sign on at a time.
I understand NAT and DAP

by computercookie

the only reason that you don't have enough CAL's to enable the release of another IP address!

by keyscapt

ok... how can I check and disable them and after I do how am I going to be assigned another IP when I only have one assigned by my ISP and my router only supports one?

by computercookie

is a node on the network, just the same as a PC, it has a static IP address assigned by the manufacturer or re-assigned by the ISP to suit their own requirements.

If you have DHCP enabled on the PC's they will find an IP from range from within the prescribed range. If you want to alter this you need to connect to the router/adsl modem via a webpage using the appropriate address and configure accordingly!

by keyscapt

I appreciate your explanation and i understand now what you are saying. I will see if this works. Any other suggestions, can I bounch off another server then to my work?

by magic alex

It's fairly simple to setup static Ip's for all your computers
1'st configure your router via the web page mentioned above to allow static IP addressing, then you will need to set the range, 192.168.1.2 - 192.168.1.7 (subnet 255.255.255.0 ) should suffice
save that and then you will need to configure each computer to use a separate IP address inside that range. This article will explain how to configure each workstation
http://netsecurity.about.com/od/quicktip1/qt/qtwifistaticip.htm
Scroll down untill you see "To reconfigure the IP address settings of a device in Windows, follow these steps:"

by magic alex

To access your routers Admin page, run ipconfig on a computer and take note of the default gateway, if you type that into your web browser you should get prompted with a login and password, your routers documentation should say what the default Admin password is (usually it is | Login: Admin | Pass: Admin | but it can differ depending on the make of your router)

by dumphrey

in the find box on the start menu type in cmd.
while holding the ctrl and shift keys hit enter to bring up the cmd window. UAC will prompt you to confirm elevation.

by ted

You could set the gateway, dns server, and ip address of the machine.. that would be a work around, or you can change the default time period allocated to a dynamic ip address.

It is probably set to 60 minutes or 120 minutes? You can also increase the ammount of ip addresses to allocate.

by dumphrey

are you connecting to your office? VPN? Telnet? The second connection is being refused by their end, based on your public ip address provided by your isp. Resetting ip addresses behind your router will do no good. You may need to get your domain admin to change your account properties to allow multiple connections.

This discussion is closed to new replies.