Question Locked

Lan connection

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Im having difficulties with creating a wireless lan connection, I have a router with wireless capabilities that is connected to the internet and I and several other computers can access the internet through this wireless router without any cables or physical connections. However these computers can see eachother but in some software applications they cannot interact with eachother, they can share and move files from one another but in these applications they are invisible to eachother. Any help would be extremely appreciated.

4 replies

by nepenthe0

1) Check the signal strength by hovering the mouse over the wireless network icon in the system tray.

Wi-Fi is short range 2.4GHz radio, essentially worthless beyond 150 feet from the access point. Here are some tips that may help reduce dropped connections:

2) A vertical booster antenna for the router can enhance horizontal coverage by ~50%

3) If the router is located one floor up or down from the laptop, consider relocating the router to the same floor

4) If the wireless adapters are 802.11g, program the router to broadcast only in [b]G[/b] mode

5) Enable SSID broadcast in your router setup

6) WPA encryption is more squirrely than WEP, but WEP is less secure

7) How important is encryption for you? If there are no likely snoopers within 150 feet, consider disabling encryption. With encryption disabled, connection is faster, data transmission faster, and there are fewer dropped connections

8) If you disable encryption, it would be wise to enable the MAC address filter in the router setup. Enter the MAC addresses of the wireless adapters, and the native MAC network card addresses of any desktop computers

9) If you disable encryption and enable MAC address filtration, periodically check for intruders. With Linksys, open the router setup, and navigate:

Status > Local Network > DHCP Client Table

The only MAC addresses posted on that table should be your own equipment. Any other MAC address is an intruder, and you can banish that person by adding that MAC address to the naughty list:

Wireless > Wireless MAC Filter > Prevent PCs listed below from accessing the wireless network

10) check for 2.4GHz radiofrequency interference near the laptops (cordless telephone base stations)

11) check for RF interference (fans, motors, hard drives, etc.)

12) check for shielding (metal cabinets, etc)

13) If still having problems, try disabling the proprietary driver and enabling the default Windows wireless chip driver.

14) Configure the router to automatically obtain IP address from DHCP.

15) Look for a strong signal (>50% signal strength) from a channel close to the router's assigned channel. There should be 5 channels between such signals to avoid interference due to bandwidth issues. For example, if you see a strong signal broadcast on channel 6, program the router to broadcast on channel 1 or channel 11.

16) Check your laptop power management. Is there a timeout for the wireless adapter? If so, configure your power management so that the wireless LAN is always enabled and powered.

17) If you have a proprietary wireless chip driver installed, disable the Windows Wireless Zero Configuration (WZC) service: Control Panel > Administrative Tools > Services > Wireless Zero Configuration [right click > Properties > Disabled].

18) You may have to do some acrobatics to get everything stable once properly configured. This is the sequence that has worked for me:

18a) Disconnect the Ethernet cable from the cable modem
18b) Boot the router
18c) Boot the modem
18d) Reconnect the router-modem Ethernet cable

19) When nothing else works, check the Microsoft Knowledge Base:

http://tinyurl.com/msqye

20) When Microsoft can't fix it, consider Network Magic:

http://tinyurl.com/66x5cn

21) If the internal wireless adapter is behaving squirrely, consider circumventing it with the Linksys USB wireless adapter:

http://tinyurl.com/3vs8r7

The Linksys adapter software works seamlessly, and is effortless to configure. if you go with an external wireless adapter, do [b]not[/b] power on the internal wireless adapter.

That about exhausts my suggestions. You may legitimately need encryption, but be aware that there is a penalty to pay for the complexities of this technology. If there are no likely snoopers within range of your access point, and you utilize MAC address filtration, and you are not overly concerned about the sensitivity of the wirelessly transmitted communication, your wireless connection will be more predictably successful by disabling encryption.

Rick/Portland, OR

by larryd4

Have you checked the firewall on the client PCs?

by jdclyde

Some of the Windows protocols do not get transmitted over the wireless because they were never efficient for use with more than a half dozen pc's on a wired lan. (which is why they switched over to TCP/IP).

What application are you working with that don't work? Do they work when you plug them in with a cable? (always test like that to make sure the application is WORKING because it might not be the wireless).

You also might have to go with a Ad-Hoc setup, depending on what it is they are trying to do.

This discussion is closed to new replies.