Question Locked

Laptop and lcd monitor problem

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm stumped and its driving me crazy. Heres the situation. I have a Compaq R4025US laptop with the 15.4" screen. I also have a Westinghouse 22" LCD monitor. I just moved into an older house from my apartment. Since the move, I am having a problem with getting my monitor to appear clear and steady like it use to. I get a lot of static if you will in the monitor now. At first I thought that it could be a problem with the electrical current and old wiring in the house so I went out and purchased a Monster Cable surge protector with the clean power 1.0 circuitry, made no difference. Then I tried an Acoustic Research power conditioner, it helps a bit. When I booted up my laptop and everything, I seen the static, but when I turned the power off and back on the power conditioner it seem to fix the problem. Now the problem is back and the trick doesn't work anymore. This is also interesting. When my power cord is plugged into the laptop, I see the biggest amount of static in the lcd monitor, but when I unplug and run it on battery, i almost completely clears right up. I've changed vga cables twice, no fix. I've tinkered with the clock and phase on the lcd screen, no fix.

So now I'm not sure if its the vga port on my laptop, the power adapter on the laptop, my monitor, the wiring in the house. Anyone have any suggestions on what I might be able to do to fix this problem.

6 replies

by hal 9000

Firstly forget Line conditioners go for the better Filtering UPS units they are just plain & simple better.

You also are probably walking on carpet and building up a massive static charge this quite often adversely affects NB's and I've seen cases when a Touch Pad becomes unusable because of the amount of Static Electricity that the user is caring.

A Cheap Air Ioniser will help with this but never completely cure the problem the best bet is to go with one of the UPS's that totally Isolates the things that it's driving from the mains so it converts to 12 or 24 V DC and then the Inverter converts back to Mains Power and your hardware is totally isolated from the mains. This will immediately rule out bad wiring in the house, being close to the end of that particular Mains line and getting a lot of spikes and low Amperage and other things like that the UPS provides what is actually needed not what's available.

Start wearing Rubber Soled Shoes, Thongs, Slippers or whatever so you don't build up a static charge and have a Anti-static Wrist Band handy that is connected to a known good earth.

That should clean up any problems with the computer & Monitor at least.

Col

PS Remember to keep an eye on the condition of the battery/s in the UPS so they don't die and allow things to return to this state. I use some 1,100 KVA Rack Mount UPS's and they are marvellous and though a bit of overkill for just one item they are big and powerful enough to drive several items so you can use them with Power Boards plugged into the back off the UPS. Most of the available Power Boards don't have the correct plug for the UPS so all you need do is cut off the supplied one and buy a plug that suits the UPS and then attach that to the Power Board and you'll find quite a lot of stuff that you can run off these units. With the smaller UPS you can expect about 2 years out of the battery but with the 1,100 that I'm currently using I've had them here for over 3 years now with no sign yet of needing replacement batteries it will be 4 years come July.

by croney1979

I have a 650 VA UPS by APC. Thats what it was plugged into before. I also brought home a ups by a company called Energizer and they don't seem to make a difference at all. Thats why i tried the power conditioner. I also don't think that I am building up much static electricity. How would I be able to tell, never been zapped or anything and my work area and desk is mostly metal and glass top.

by hal 9000

The most common is a backup power provider for when the mains fail and then you have the Isolating Kind where the Mains are Isolated from the Computer or anything on the other side of the mains.

+This involves turning the Mains Voltage into a 12 or 24 V DC Supply and then the Batteries feeding an inverter and providing Mains Power to the devices connected to it.

The problem with Line Conditioners is their reaction speed most are way too slow to be of any use. If you look at the Specifications you should see a reaction time to Spikes and Over Voltage events if the figure is above 1 Nano Second it's no good most work somewhere around the 4 Nano Second Mark or slower.

The average UPS doesn't actually Filter the power it just provides a Backup supply in the event of a Mains Failure so you are not getting any Surge or Spike Protection. Even the Filtering ones don't offer Perfect Isolation from the mains but at least by breaking the Voltage down to 12/24 VDC there is less likely hood of problems occurring.

As for the Glass Top Table with the metal frame try earthing the frame and then touching it when you first enter you just might be surprised. As Glass is a very good insulator you are unlikely to get a hit from the glass and the metal will be unearthed so at worst you might get the occasional jolt as you discharge and bring the frame to the same Electrical Potential as you body has or at least discharge any excess charge off you into the table frame and slowly build up the Static Level of the frame. As these are generally Not Earthed you'll never actually know what's going on unless you are exceptional and build up enough Static to make your hair stand on end but this isn't very common. :D

I had one person who would regularly Zap any clients as he reached out to shake a hand or the insane Tech who got a little too close while looking over his shoulder trying to figure out what was happening. After I fitted a wrist strap onto his work space I never had another problem from him zapping anything again though he did provide quite a few other problems that no one else could recreate. :(

Perhaps you should try a Recording Device which records the available power over a period of time on paper. These are available from your energy supplier when problems are present.

The only other time that I've ever seen anything like this was in a business where next door they had a Dentist who's X Ray machine was leaking and the poor function of the computers where the least of their problems once the problem was tracked down.

As it's unlikely that you are sitting on top of a Radiation Source look for strong EMF Fields around the place or if you are close to high power Radio/TV Transmitters or Transceivers that may be the problem. If that's the case the only real alternative is to turn the room that the NB is in into a Faraday Cage by covering the walls. Ceiling and under Floor with some kind of metal that is all connected together and earthed. Generally things like this are not feasible but if you can locate an intense EM Field you may be able to coat an internal wall between the field and the room with some form of Aluminium and earth that or maybe Aluminium Cladding on the outside of the house will do the same job. Look first for Ham Radio Aerials or the like before you even consider trying anything though.

Military Radar can have the same effect so if you are near a Military Air Base or a Naval Base you may be adversely being affected by their emissions possibly even a civilian Airport could do the same thing. You may need to look around your area for possible sources of intense EM Fields and then see what if anything is possible to do to prevent these entering the room that you have the computer in. I take it that only the NB and it's monitor is being affected and your TV is working properly. If not you should really have a hard look at the Mains particularly if the TV Screen shrinks top to bottom when there is a high load on the mains or if you have an electric stove you can not run all the hotplates at the same time.

I hope that at the very least gives you a starting point to work from.

Col

by croney1979

Can you elaborate more about the correct UPS I should be using? What brand, model, price? Where should I go to purchase one?

by hal 9000

It really depends on what is available where you live or at the very least near where you live. A good Filtering UPS is worth it's weight in Gold as it just about totally isolates the connected devices from the mains. The down side these are more expensive than the standard UPS as those are only to supply backup power in the event of a power outage.

The Filtering ones are working all the time because there is no direct rout through the UPS to the other side it breaks down the Mains to DC at whatever Voltage the Batteries support generally 24 V DC and then there is an inverter running all the time turning that 24 V DC to Mains Power So it's much more stable.

I've been using several of these

MGE Pulsar Evolution 1500VA 1000W UPS, Tower, Line-interactive, USB and Serial, Output Voltage: 230VAC

With them Racked Mounted and feeding the different items one will drive 7 computers 4 Monitors 1 Monochrome Laser Printer and a couple of Ink Jet Printers as well as the ADSL Modem and some external USB Drives and Speakers without batting an eyelid.

Though I wouldn't recommend to turn everything on at the same time.

Col

This discussion is closed to new replies.