Question Locked

Lightning Strike--But it Works Except for

0 helpful
29 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,
A Lightning Strike caused my Laptop Inspiration not to connect to the Internet.

I have done a complete Format of Drive, Loaded ALL Software that machine was built with and it works fine, like new except under Hardware it says that the Cable is unplugged. I suspect that the Internal Modem (dell # H9379) got fryed.

My question is, could it be anything else? I want to purchase this part as it's only about $30.00 delivered. Thanks for the Help.

29 replies

by thumbsup2

You said that it displays a message saying a cable is unplugged. That is for a network 'card' (NIC). However, you suspect the modem is fried. These are two different components.

How was it that you were connecting to the internet before? Do you have a dial-up ISP or are you connecting through DSL/CABLE? If it's the latter, have you checked the external device which allows you to connect (DSL/CABLE Modem, router, switch, cables)?

by older mycroft

It didn't make any sense to me either.

I'm also wondering what this lightning strike 'actually' was? [i]Maybe not lightning at all.[/i]

by thumbsup2

I don't know what the weather has been like in Massachusetts lately. But, out on the West Coast, lightning a common occurrence during certain seasons. Anybody who doesn't run off of a good UPS with everything, including phone/network being filtered through it, is just asking for trouble. Even if you don't get hit directly, the surge through the phone lines/network can fry lots of things.

by bosco murphy

Hi, I am plugged directly into the Cable. There is no phone jack, just Cable. If I plug into my other PC or Laptop the Internet works fine. The Laptop I am having trouble with is a Dell Inspiration #E1505. I went onto Dell and put my Service Tag in and it showed everything the Laptop was shipped with.I did not see anything about a Network Card, just a Modem Componant #H9379. This is what I am suspecting is blown, am I correct?
Thanks PS. Service Tag (Dell) H2CCR91

by thumbsup2

You said, if you plug in to the other PC, the internet works. This indicates you have a NIC (network plug-in).

According to the as-built specs for that service tag, there is a modem and NIC both. Even the service manual for that computer shows there are both.

http://support.dell.com/support/topics/global.aspx/support/my_systems_info/details?c=us&l=en&s=gen&~tab=2&servicetag=H2CCR91

http://support.dell.com/support/edocs/systems/ins6400/en/om/specs.htm#wp1054574

So, if your internet works when you plug it into the other PC/laptop (using the RJ45 ports) and it does not work when you plug directly into your cable modem, the problem is in your network configuration. You probably have it configured to share an internet connection through another PC. Since it can't find the other PC, the internet is 'down'.

Try connecting it directly to the cable modem, then go through the Network Setup Wizard. This time, use the option that it connects directly to the internet, not through another computer.

Now, if you want all 3 computers to connect to the internet simultaneously, you'll need to purchase a router, connect it to the cable modem, then connect all 3 computers to the router and use the Network Setup Wizard on all 3 of them which would be set to connect directly to the internet through a router (get IP address automatically).

by jdclyde

it will pay to have this fixed, if you do.

Check your policy, and then take it to someone to fix, and then submit the bill to your carrier.

Good luck with that.

by oh smeg

Rise times with Lighting Strikes are in the Vicinity of under 1 Nanosecond while most of the better filters have a switching time of 2 to 3 Nanoseconds so by they time that they turn off and shunt the excess power elsewhere the damage has already been done.

Even if there is the best possible Surge Protector in Place I just wouldn't even consider trussing then to stop a Lighting Strike. Where you can go from Mains Voltage to well in excess of 400,000 Volts in well under a Nanosecond. I just don't know of any device that can shunt that much energy safely. :D

Here I have a filter wired into the Mains which states that it can stop a Lighting Strike from 100 Meters away or more. This costs the earth to buy and then you need a Electrician to fit it and even with that in Place I still unplug everything during Thunder Storms.

I can remember years ago when I attended a place where the Main Frame had stopped working. I started at the obvious thing and pulled the Power Supply apart to find that it was working perfectly. Then at a frame when I pulled the covers I found Carbon and not much else inside. Had me a bit confused back then as whatever had hit this place had not come over the mains or had been so intense and sudden that the Mains wasn't affected.

So I asked to use the phone there and was informed that they had suffered a Lighting Strike to the Box outside that handled the Phones and that entire system was destroyed.

Seems that no one connected this with the computer as what it used to connect to the Phone Lines wasn't something that they ever touched but used hourly. :D

It did however make it interesting when opening all of the terminals which where also destroyed.

Col

by thumbsup2

Years ago, when everyone still used dial-up, one office in another town lost 15 computers due to a lightning strike which came through the phone lines. It not only fried the modems, it welded them to the motherboard. They too had a UPS on each of the computers, but nobody thought to protect the phone lines attached directly to each of the computers. Their reasoning was they didn't think those little tiny lines would conduct electricity! :0

by bosco murphy

Oh Boy I have a few questions and a wee bit confused.
I took your advice and did the Network Connection thing again, BOTH WAYS. (1) a direct LAN connection, no good, and then a connection thru an other PC, No Good.

This is my nefhew's laptop and he is taking it to Afganistan 1/2/09. He can not have Wireless enabled so I shut it off in the BIOS.
Just a reminder that I did below.
Reloaded XP, full Format NTFS
Nothing else on system just OP sys etc.
Machine starts real quick and everything works fine except for this Internet problem.
He is at Ft.Bragg and had Lightning a month or so ago, I'm in Boston.

Is the Network Card soldered to the Mother Board? Or can I replace it by removing plug/screws etc?

I also downloaded and installed all Drivers that this Laptop came with from Dell's site, everything even the optional stuff.

I really appreciate your help as I am an
M.E.and only a novice/intermiate when it comes to Computers.--Thanks---email me murphy275@comcast.net

by thumbsup2

It's actually built into the MB. It's not replaceable. However, if you can't get it to work by following all the rest of the instructions, you can buy a PCMCIA network card or even a USB network adapter .

by thumbsup2

You said you reloaded XP, full format, NTFS, nothing else on system.

Did you look in the Device Manager to make sure the drivers for the NIC are installed? If it's not functioning, you would see a yellow exclamation point on the device listed under Network Devices. Do you see any devices with yellow or red marks on them?

by bosco murphy

Yup everything is fine there, no yellow or red ticks.

The Adaptor is loaded and the Broadband is loaded also.

From the Dell site I saved and Loaded all of the Drivers etc, Bios Flash, Chip Set, Vid/Audio and even the Optional ones.

I think today I am going to buy either a PCMCIA Network Card or a USB Network Adaptor to see if I can get it running. I have heard that they run a wee bit slower than being connected directly to Cable via the built in NIC. I will go to the store and see what they recommend. I also called my Cable company and when I told him the symtoms about the Cable being unplugged he said that the NIC most likly failed.

I'll let you know, Thanks Thumbs

by rob miners

Check that the PC's network card is OK.

Click Start, Run and type cmd and press Enter.

At the prompt type ping 127.0.0.1 and press Enter.

You should get a display like this do you.

C:\>ping 127.0.0.1

Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128

Ping statistics for 127.0.0.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms

Keep us informed as to your progress if you require further assistance. ;) :D

by bosco murphy

Hello Jacky,
I just did your suggestion "Pinging" ant the cmd and it came back exactly like you said it would.

I just tried IPconfig (release & then Renew) and it said "No operation can be performed while it has its Media disconected"

Not sure what this means????

Thanks. I like your flag. I worked in Inverness for 1.5 years. Beautiful Country.

by rob miners

my mate CaptBilly1Eye knocked it up for me. Glad that you liked over here. :D

Windows XP

Click Start and go to Control Panel.
Click on Network and/or Internet Connections depending on your view.
Click Network Connections.
Right click on Local Area Connection and choose Properties. If this icon does not appear, then your network card is not being detected by Windows. This icon should appear automatically if your card is detected. If its not being detected try reinstalling the Network Drivers.

Under the Connect Using label, make sure that your network card is properly listed.
If you look below you will see a drop down box, there will be a list of all installed/available protocols for your network card. Scroll down and find the "Internet TCP/IP".
Highlight this entry and click on the Properties button below the list. If you have pre-configured values in this window, you may want to write down the information for future reference. Then, make sure that the option "Obtain IP address automatically" has been selected. Also, make sure that the setting "Obtain DNS Server Address Automatically" is set.
When these two properties are set, go ahead and click the "OK" button to close the Properties panel and click "OK" again to close the control panel. Windows may or may not ask you to restart.

Start, Run and type CMD and press Enter.

type netsh int ip reset reset.log and press Enter.

type netsh winsock reset and press Enter.

Reboot the PC.

Keep us informed as to your progress if you require further assistance. ;) :D

by bosco murphy

Hi,
OK Im in the Manager and this is what I have. I Don't have anything that you mentioned in your post only these (3) things below which I think are related to Network.

Broadcom 440x 10/100 Intergrated Controller
Intel(R) Pro/Wireless 3945ABG Network Connection
1394 Net Adapter
Oh and OHCI Compliant IEEE 1394 Host Controller
Conexant HDA110 MDC V.92 Modem
SDA Standard Compliant.
Out of all the things listed I have no + sign listed, so I can't expand.

by thumbsup2

Jacky gave you a link to it. Try it and see what it reports to you.

No + sign? I'm not sure you're looking at the Device Manager, or possibly you have it set to some type of 'view' that lists everything all in a row. But, what we're looking for isn't on your list.

Do what Jacky says and go to the Dell Diagnostics web site.

by bosco murphy

Hi Jacky, I have done this already, i.e. obtain IP and DNS automatically etc.
I also tried ipconfig /release enter and then ipconfig /renew
No luck as it comes back and says that it CANNOT because the Media is disconnected and it can't perform this function.

I tried your first cmd for netsh int reset reset.log and nothing happened.

I then tried netsh winsoc reset and that worked and then it told me to reboot, I did.

Still no change. Please read my comment to Thumbsup above as I am going to buy a pcmcia card or else a usb network adaptor.

I'll let you know--Cheers

Oh--In the network prop's I do have all the stuff I believe. Client, TCP, and the other things, Service etc. So the stuff is there but still no go. I also yesterday did a complete XP install/format again and after that did all the Dell Drivers etc. So again there is absolutly nothing on this except for XP. No other Software network stuff i.e. Active X or SP 3 (XP) because I cannot connect.
Cheers

by bosco murphy

Hello,
Well I bought a new Linksys PCM ver.2. It only sticks in the Slot about halfway. Followed the directions by booting up for XP and waited for the new HW message to come on, nothing. No lights are blinking on this device either. This is a Etherfast 10/100 CardBus PC Card. Boy I'm stumped now.

Any suggestions, I hate to be a pest and very much appreaciate all your help so far.
Cheers

by thumbsup2

... go with the PCMCIA network card. Laptops traditionally don't have enough USB ports to begin with. Why waist one on the NIC? Usually, people don't use their PCMCIA slots all that much, so put one of them to work.

by thumbsup2

You didn't, by chance, stick it in the floppy slot thinking that's where it goes, did you? The PCMCIA slots are just barely wider than the card and it should slide in, with a little push till it seats, nearly all the way leaving just the black housing around the cable plug sticking out.

by bosco murphy

Hi Thumbs,
The Site here said I am at my Max Posts so I am going around it a bit.

Re: To your Right Slot Post. Yes I am in the right Slot. I pressed the plunger and the Plastic Card popped out, then I inserted the PCM. It actually only goes in about half way and I believe I can feel the Pins/Slot making contact when it seats itself in there.
This Slot is on the RT side and the salesman over at Micro Center showed it to me. THX

by thumbsup2

No problem replying to a post above to continue... that's how we do things around here.

So, if you're sure it's pushed in as far as it can go while the computer is running and it's right side up and Windows doesn't detect new hardware and you're sure you've installed all of the motherboard drivers to run these peripherals, I think we're going to have to assume there was more damage to the laptop than the on-board NIC.

But, let's check something first....

In the device manager, do you see a top level listing for 'Network Adapters'? If so, expand the plus sign and tell us what device(s) are listed below it.

While you're there, do you see a top level listing for 'PCMCIA Adapters'? If so, expand the plus sign and tell us what device(s) are listed below it.

If you don't see either of these devices, there's a strong possibility that either they're turned off in the the BIOS, or the motherboard is damaged. Let us know what you see. If you know how to get into the BIOS, do it. If you don't, we'll handle that later.

by bosco murphy

Hello,
Well it turns out that I had the wrong PCm Card. When it did not fit into the Slot like I said before and I wondered about it, it turns out that I needed a Card for an Express something.
Anyway I tried a USB to LAN and it worked.
When I brought the Laptop to the Micro Center store and told my problem they sold me the wrong one, even after (2) people looked at it. Hope I can get my $$ back on the device that I bought which was the wrong one.
Thanks to All for your very helpfull info here, I learned a lot
Cheers and Merry Christmas

by thumbsup2

At least the Nephew will have something to take with him. Give him a hug and a big THANK YOU from all of us before he deploys.

And don't you be a stranger either. Hang around. We're one big fun loving community here. :D

by rob miners

I am sure that you will get a refund when you point out their mistake.

Merry Christmas to you and your family. Have a good one.

This discussion is closed to new replies.