Question Locked

Motherboard good, PSU good, but my PC does not power up!!!!

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi everyone...

This is my first post here...

The problem I am having sounds very general but it really isnt.

One day my PC turned off all by itself. I have a UPS and there was no apparent loss of electricity in the house or any lightening. After that incident my PC doesn't turn on. No fan, No lights!!!

I have checked the following components and found out they're working:
1. Motherboard - took it back to the shop, and they checked it against their hardware and it works.
2. PSU- Checked it with a friend's computer and this is working aswell
3. CPU,Memory HD, DVDRW ..all are working.
4. Power cable is checked
5. No switch at the back of power supply
6. Connectors are all fine

yeh now the big question is WHAT THE HELL IS WRONG if everything is ok? ...that's the answer I want to find out....please let me know of any suggestions...thanks.

7 replies

by patb071

You try plugging it into a different power outlet or power cord? Do you know how they tested the mother board? If you push the button to turn the computer on in the front case maybe that button is stuck? Sounds like it may be something simple.

by clarkd038

Start by having only the power supply plugged into the motherboard- RAM out and no connectors to the HD, and see if you get any lights/beeps or anything at all. Did you try plugging it in to a different outlet, or verify that the outlet was working properly?

keep us updated.

by snuffy09

that is good advice. when troubleshooting something like this (when nothing makes any sense), start with the barebones and work your way up adding one device at at time. Sometimes the problem isnt as obvious as just being a fried PSU or mobo.

In my opinion it sounds like the PSU... Just because it works in your friends computer doesnt mean much. Im not going to assume you guys are running the exact same hardware on your computers. Your rig may be drawing more power than his. If the PSU is failing it may not even attempt to start your computer.

by slayer_

As it, it is getting no power at all, no fans, CD's, nothing, or it is turning on but nothing is happening, fans and such turn on, but no picture and no activity.

by snuffy09

"my PC doesn't turn on. No fan, No lights!!!"

by oh smeg

As for your problem have you thought that the PS may not be compatible with the M'Board? It is possible that everything works by itself but once they are put together they do not. You need to test this out of the case with the M'Board on an Anti Static Surface or if you don't have one of those some clean white paper. What can happen is that a PS changes it's values and goes out of tolerance so that it no longer works with that Particular M'Board but it may run another M'Board that requires less Power or Current. It may originally have been above it's design specification through a combination of Manufacturing Tolerances but over time these Electronic Components had gone off slightly causing this unit to no longer be sufficient for that particular M'Board.

What is important here is to make sure that all the Power Connectors to the M'Board are correctly plugged in that includes the Supplementary 12 V 4, 6 or 8 Pin plug as well as the 20-24 pin ATX Plug.

Also check for bent pins on the CPU or the CPU Socket as here I'm assuming that the CPU was tested on a different M'Board. While you have the M'Board out of the case check the front panel switches with a multimeter if there is no resistance through either the Power On or Reset Switch the one with no resistance is either stuck in the On or open position or has failed.

Something I have seen several times with the cheaper cases is that the Reset Switch Cover gets clogged with Dust and other airborne Crud and along with a poor molded Plastic Cover causes the Reset switch to stick in the On Position. The cure here is to remove the reset switch from the front panel and then the plastic cover/button and file away the rough edge on the molding till it can not longer stick. You could to double check this remove both the Power & Reset Switches from the M'Board and plug the Reset Switch Leads onto the Power On Pins of the M'Board and see if that turns the computer on. If the system starts as soon as power is applied that switch is sticking in the On Position.

The other thing you can do here with a small screwdriver and both sets of leads for the Power & Reset Switches unplugged is to short out the 2 pins for the power switch and see if it starts now. If it does one or both of the front panel switches are sticking in the On or Open Position. You should also test these switches to see if they are working when they are closed there should be no circuit through the Switch and when pressed in there should be no resistance through the Wires or Switch.

If you could be more specific with the Make & Model of the M'Board, CPU, RAM & Power Supply we may be able to be much more specific as to where to look. ;)

Col

This discussion is closed to new replies.