Question Locked

my network isues

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I currently am having some issues setting up my network at home. I have 2 NetgearWPN824 routers and need all my computers connected wirelessly to them, with my DirecTV DVR's and XBox360 connected directly to them via ethernet cables.
Currently I have the following:
--TWC cable modem on 2nd floor connected to 1 WPN824 and have DHCP enabled on that one with the server starting at 192.168.1.2 and ending at 192.168.1.98. This router has a DirecTV DVR connected to it via ethernet cable, and also typically has 2 desktop computers wirelessly connected to it.
--Then I have the second WPN824 on the first floor (connected to the one on the 2nd floor via Powerline adapters plugged into the LAN outputs) with its IP Address set to 192.168.1.99 under the LAN IP Setup tab and also DHCP unchecked. Thats all I changed in it, I didn't change anything for the Internet IP under basic settings.
-- I did however have UPnP unchecked on that router(1st floor) as I have my xbox360 connected to it and had it set to connect to the IP in the DMZ on that router as before this one was my only one i had and used and the 360 just worked best in DMZ address.
The only other thing connected to that router is a DirecTV DVR that I need to be able to access the network freely so I can share media with it from my laptop that usually connects to the router on the 1st floor.

As of now when I connect wirelessly to the router(1st floor) I can use the internet fine but in the Network and sharing center in vista it says connected but still "Identifying..."
Also I have my PC set on both routers to be reserved to a specific IP but when I connect wirelessly I do not connect to that address like I used to be able to in the past.

Okay, sorry for the long post here just wanted to get as much info as possible. My main thing is being able to figure out why it still says "identifying..." and also why I can't connect to the reserved address automatically anymore. Also how should I set my 360 to connect to a DMZ exactly. I'm willing to change the configuration if theres a better way but this was just what i saw on netgears site as before I had them connected together and ran the setup utility cd that the routers came with but I had the router on the 1st floor connected into the WAN outlet and it caused problems when I wanted to connect to another computer in the house that was connected to a different router.

9 replies

by jwslaugh

bumping it up in hopes someone will catch this and offer a little help with my issue.

thanks in advance

by cg it

2 routers= 2 networks.

a wireless access point would suit this setup and eliminate the configuration problems inherent with 2 routers.

to fix your problem, for the second router connect the WAN port to a lan port of the first router. provide an address in the first routers subnet. use your ISP DNS server addresses for DNS.

Change your second routers LAN addressing to something different than your first routers lan address. if your first router's lan address is 192.168.1.1 then use 192.168.2.1 for your send router.

by jwslaugh

I set them up the way I did based on what I have read around and have been told to not plug the 2nd router via its WAN port and should instead connect it Via LAN port from R#1 to a LAN port on router #2 and set the 2nd routers IP to something outside what the first router is set to give out.

I will try this later tonight if you think it will be a better set up. These two routers are all i have and I just want something to where I can access something easily thats connected to the 1st router from my laptop being connected to the 2nd one. and also be able to put my xbox360 in DMZ being connected to the 2nd router. My thing there is being in the DMZ on Router 2, does it still really be in DMZ even though Router 2 is getting its internet access from Router 1??
Currently Setting DMZ on Router 2 and all does nothing as i have DCHP disabled on it to allow Router 1 set all the ips.

thanks for the response btw

by cg it

because you bypass the router function of the router and are only using it's built in 4 port switch. That's where the wireless access point comes in. It's not a router and provides wireless access.

A DMZ port is a port on the router that the router's firewall doesn't protect so any computer or other device is exposed to the internet unprotected by a firewall.

an example of 2 routers connected together in a home environment would be:

1st router WAN your ISP defined settings
1t router LAN default values typically 192.168.1.1 or 192.168.0.1 depending on your router brand.

2nd router WAN port : configured with an address on your 1st routers LAN e.g. if your first router's LAN is 192.168.1.1 mask 255.255.255.0 then the 2nd routers WAN would be a static address of 192.168.1.10 mask 255.255.255.0 DNS your ISP DNS server addresses.

2nd Routers LAN needs to be on a different subnet than the first routers LAN. you can use 192.168.2.1 mask 255.255.255.0 or you can use mask 255.255.255.192/224/248 etc.

the computers connected to the 2nd router would then have addresses 192.168.2.15/16 etc mask 255.255.255.0/192/224/248 etc default gateway is the 2nd router 192.168.2.1 and DNS servers are your ISP DNS server addresses

by jwslaugh

I'm pretty good with computers but got a lil lost there.
So the better way to hook it up would be to run a cable from router 1 to the WAN port in router 2 and put the second router on a static IP (under basic settings)thats in the range of the 1st router's values.
Then under LAN IP setup change the IP address to one outside the 1st routers range.

Do i need to re-enable DHCP server on router 2 doing it this way?

Also if I put my 360 in DMZ address set up on Router 2, then will it really be fully open to the internet?? I just ask this because this router is still getting its access to the internet through router 1 and i would think I would have to have the 360 set up in dmz there. I put it in DMZ as its the best way to get it open to the internet which is what I want since nothing important is on my 360.
Also, with the different ip subnet's (ie. 192.168.1.1 vs 192.168.2.1) will the PC's connected to the latter subnet be able to fully communicate easily and view the other devices on the 1st subnet?

I am doing this with 2 Netgear WPN824 routers btw.

currently I have both subnet masks set to the default 255.255.255.0 and under basic settings have them set to Get IP address automatically but the LAN IP setup in router 2 set the IP addy to one outside the subnet set for router 1(ie router 1 is set to start at 192.168.1.2 to 192.168.1.98, and router 2 is set to 192.168.1.99 with DHCP unchecked as its connected via LAN ports and not WAN)

thanks for the input and help so far!

by jwslaugh

bump it up for you to hopefully catch my reply so i can hopefuly for once and for all get this figured out and hooked up the best way possible.

by bens

I understand that you are using what you have, but I think you would have a lot less trouble using a cheap unmanaged switch. You should still be able to use your Powerline devices as an uplink from floor to floor. Keep a single DHCP server active on the router and let assign addresses throughout.

by cg it

still has the firewall on Router 1 protecting it. It's a DMZ on router 1 that would make any computer using it naked on the internet.

Best way to explain routing and routers is that a router creates a network. as an example: if you get DSL from your ISP and hook up your computer to it [straight CAT 5 from PC NIC to DSL modem and you set your NIC to obtain addresses automatically] your computer is really a host on the ISP's network [one BIG network]. If you put a router between the modem and your computer, what your doing is creating a seperate network [your own] from your ISP's. Any host behind the router is no longer on the ISPs network. If you hook up a 2nd router to your router, your creating another network.

next comes addressing. Routers route packets by inspecting it's address. If the packet is NOT destined for the local subnet, it's sent to the gateway to be forwarded to the next router [next hop]. If your first router has the same addressing scheme as your second router including the same default gateway, the 2nd router will not know what to do with the packets. Routers always check the address on packets to determine what to do with them. If a packet has an address of 192.168.1.2 and your routers LAN is 192.168.1.1 the router will try to get the packet to the host with the address 192.168.1.2. if it can't find it, the router will drop the packet. Imagine if your 1st router LAN also has the same address 192.168.1.1. as your second router LAN. 192.168.1.1 . Your second router will never send packets to the default gateway that are intended for computer on router 1 network because router 2 thinks the computer is on it's network because it has the same addressing scheme [private Class C].

So you have to make router 2s LAN a different addressing scheme than router 1s LAN.

a simple matter of changing the 3rd octet and/or using a different subnet mask. [subnet mask masks the host portion of an address to determine the network the host is on].

So, your diagram for your network with 2 routers would look something like this:

1st router WAN ISP address ISP DNS
1st router LAN 192.168.1.1
[router's address]
1st router gateway 192.168.1.1
[routers address]
1st routers address pool 192.168.1.1 through 192.168.1.254

2nd router WAN Static address on 1st router's LAN [192.168.1.223]
2nd routers default gateway = 1st routers address.
2nd routers WAN DNS ISP DNS addresses
2nd routers LAN router address]192.168.2.1
2nd routers LAN default gateway [router address 192.168.2.1 that you use for computers behind it]
2nd routers address pool 192.168.2.1 - 254

you can change the subnet mask to however many hosts you want to have on the network.

255.255.255.0 allows 254 hosts on the subnet.. 8 bits available on the 4th octet]

This discussion is closed to new replies.