9 replies
by sounforgettable Accepted solution
by 1bn0 Accepted solution
From 192.168.1.0
To 192.168.?(2).0
Right now the modem address is in the same range as teh rest of the internal network. So I would expect the router is not sending anything to the WAN port.
Then it should see the modem as a different , upstream network
by sounforgettable Accepted solution
I use Auto IP settings at the moment so have just relied on what Vista chooses for me, stupid thing to do really! I should know by now that Vista rarely does what it's supposed to do.
I'll go and give that a try
Thanks!
I'll let you know how I get on.
by sounforgettable Accepted solution
I've just altered the settings so that the Router was 192.158.1.2 with a default gateway of 192.168.1.1 and the PC @192.168.1.3. The IP I got from the router was a dyamic IP as this is required by Tiscali the IP was something like 88.111.??.? I forget but it's dynamic so doesn't matter as it will change the next time I connect anyway. Still I cannot access the Internet. I also went and upgraded the Firmware of the router to the latest supplied by D-link but this just agrevated the modem a little and it took me a further 30 minutes to get my Internet connection back again with just the modem connected.
Damn I'm frustrated! I've never known anything be this difficult before! Someone please help. If this is something you've experienced, I'd be happy to hear how you fixed it.
by sounforgettable Accepted solution
by robo_dev Accepted solution
The confusing part of it is that many modems are actually simple NAT routers, and hanging one NAT router off another NAT router does not work well.
If your D-Link was truly a 'modem' your PC would be assigned a real Internet address like 24.x.x.x or something similar...since your PC is getting a 192.x.x.x off this 'modem', it's not a modem, it's a router.
There are two solutions to the problem:
a) Assuming you have DSL, put the D-Link device into 'bridge mode' so that it no longer acts like a router. The Netgear can then treat it like a modem, which it is, effectively, in bridge-mode. the Netgear router would then have to perform the authentication to your DSL provider, using the username/password provided with your provisioning instructions.
b) If the D-link device appears to have some reasonable firewall built in (which it probalby does), then you plug it's LAN port into a LAN port on the Netgear.
You then disable DHCP on the Netgear, and set a static IP address to the LAN interface to be something consistent with your network.
in this case, you've effectively transformed the Netgear from a router to a combination Ethernet Switch and Wireless LAN access point, which is what you need to plug into your d-link router.
by sounforgettable Accepted solution
by robo_dev Accepted solution
That model has two modes:
Bridged Mode
Routed Mode
It's currently in 'routed mode'
You want to get is switched over to 'Bridged Mode'.
Be aware that you will need the original DSL provisioning info to plug into your Netgear Router...some routers can do some sort of 'setup wizard' routine to make the DSL setup process easier.
ftp://ftp.dlink.co.uk/dsl_routers_modems/dsl-320t/DSL-320T_user_guide.pdf
by sounforgettable Accepted solution
Many thanks Robo_dev! I'm sure that would have worked a treat but I have been doing some digging of my own and found that the router I have is a Cable router (DSL) not ADSL for use with a standard telephone line. My set up needs and ADSL router which I just discovered are only sold with inbuilt modems. I just went and swapped it out for one of these so all sorted. I guess the moral of this story is to read about what you need before you just go headlong into a field you have limited knowledge of. So for twits like me : If you have a conection through a standard (BT) type phone line, you will need a modem router like the Netgear DGN 2000, but if you have cable or a set top box conection then you need a standard router!
Thanks for your support!
This discussion is closed to new replies.
Trending Windows Forum posts
Sort by Trending