Question Locked

New video card, no monitor signal....

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have been upgrading my computer and have run into a problem. At the moment the computer stats are as follows:

Asus Maximus motherboard
4 Gigs of Corsair 6400 memory
Intel Q6600 Quad core processor
Raptor 75 Gb 10,000rpm hdd
one 300 gb hdd
two 500 gb hdd's
620 watt Enermax Power supply
Sony DVD burner
Windows Vista Ultimate 64 bit

I had a Asus 7800 GTX video card but wanted to upgrade it to something that ran DirectX 10, and found the Radeon 2900 Pro 1 gb.

Everything was fine until I installed the Radeon card. The (extremely loud) fan on the card started, a red light on the card came on, but the monitor did nothing. I could hear all the usual beeps and sounds of the pc but the monitor was blank. I put the 7800 back in and everything was fine. Now the crazy thing that happened... was that when I bought the card the guy at the store said 'wow, I've never seen a 1gb video card before' and opened the box and picked up the card! This was before I bought it and at that point I should have run, but I didn't.

Other than the possibility of the sales guy frying the card, is it possible the PSU is not powerful enough? Is there a good way to test for these or other possibilities? Is there anything else that would cause this problem?

Thanks!

9 replies

by mjd420nova

It is possible that the sales guy did toast the card, but it would be rare. Does the card require another connector directly from the power supply?? The P/S should be big enough, just barely, especially with three huge hard drives you have. Did you even see a POST? If the unit sounds and acts like it's booting but no display and you can't get into the BIOS, then the video card is most likely bad. Shoot the salesman.

by write2scott

Yeah, the card has an extra 6 pin power connector which I plugged in.
The monitor stays completely black, and the light on the monitor doesn't change from orange to blue either. I can see all the peripherals (keyboard, mouse, wacom) lights blinking, but nothing from the monitor.
I think my PSU is just not enough. I'm going to try and unplug all the big HDD's (less power used) and see if that gets me anywhere, then I'll know the PSU is too small.
Thanks for your reply!

by maniacman

I've seen this problem all too often and most people panic into thinking that either the mobo is fried or the video card is toast, if not both. Make sure the video card is absolutely compatible with the mobo and that the power supply can provide enough juice for everything that the system will have. If there is insufficient power, the most you'll see are the cooling fans spinning, but you'll get no display and no POST or beeps.

by write2scott

I'm sure the mobo and card are compatible, the mobo has two PCI-E 16x slots and is Crossfire compatible, but I think the PSU is probably too small. This card apparently uses over 200 watts by itself...

Thanks for the reply.

by jamesrl

Stupid question I know, but did you plug in the power connector from the PSU to the card? Did you try unplugging and replugging to make sure its properly seated?

The 2900 is a very power hungry card. Just because there is enough power to get the fan running doesn't mean the card is getting enough power.

BTW, I would have bought one of the new 3800 series cards instead - they made the the chip from the 2900 smaller, needs less power generates less heat. And they are less expensive - and very close in performance to the 2900. And unlike the 2900 (or the 8800 nVidia) they support the new DX10.1 standard.

James

by write2scott

Yeah, I plugged in the 6 pin power connector to my PSU, but beside that plug is another space for 2 4-pin (8 pin?)connectors, but I believe that is for overclocking. After looking around on the net I read somewhere that this video card alone uses over 200 watts of power... so I think I might need a new PSU to keep up. But I'm going to try and take it back and get at the 3800, or a new 8800 GT if I can find one instead.
Thanks for you help!

by oh smeg

http://tinyurl.com/3aewax

Here are the system requirements as stated by AMD

System Requirements
PCI Express? based PC is required with one dual-width X16 lane graphics slot available on the motherboard
Connection to 550 Watt (750 for CrossFire?) or greater power supply with two 2x3-pin PCIe? power connectors is required.
For enhanced performance with ATI Overdrive?, a power supply with one 2x3-pin and one 2x4-pin PCIe ? power connector is required
Certified power supplies are strongly recommended. Refer to http://ati.amd.com/CertifiedPSU for a list of Certified products
Certified system cases with good airflow and cooling are recommended. Refer to http://ati.amd.com/certifiedcases for a list of Certified products
1GB of system memory
Installation software requires CD-ROM drive
DVD playback requires DVD drive
Blu-ray / HD DVD playback requires Blu-ray / HD DVD drive
To complete the CrossFire? platform, a second ATI Radeon? HD 2900 graphics card, a CrossFire? Ready motherboard and one CrossFire? Bridge Interconnect cable per board (included) are required

listed here

http://tinyurl.com/2m27lf

by inachu

I always dust my pc before insertign new hardware.

Next is your power supply at least 500 watts?

Next after this did you plug the power into the video card?
Many newer video cards need extra power.

Did you uninstall the older video drivers as it would help in a diagnosis such as this.

This discussion is closed to new replies.