Question Locked

NO VIDEO SIGNAL

0 helpful
26 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,
I have an ASUS P5N-E SLI motherboard. Installed are two sticks (1Gig each) of DDR2 RAM, a EVGA GeForce 7950 GT PCIE video card, Intel Quad core processor, etc. When I power on the computer, the mobo light goes on, the PSU powers on, and so does the case fan and the the video card's fan. What fails to go on is the CPU's heatsink fan. Also I get no video signal on my LCD. I tried using a brand new video card to see if the video card is the problem, but I get the same error with the new video card. So the video card is ruled out.
Has anyone experienced this problem before?
If the problem pointed directley to the heatsink fan, then I should at least get a few seconds of video on my LCD. I get nothing but, "NO VIDEO SIGNAL"

Thanks

26 replies

by oh smeg

When you turn on the computer?

If so change the Power supply and provided that everything else is OK it will work.

I had a customer buy a New M'Board, CPU, Video Card, RAM and so on till he had replaced everything but the Case & PS. He then brought it in to be repaired and I replaced the PS under guarantee for him and he had what was effectively 2 working computers he just needed to buy another case & PS.

His reasoning however what that as the fans where running the PS was working but when I explained to him it only meant that the Fans where getting a nominal Voltage somewhere around 12 V and a unknown Current let alone the other Voltage Rails may not have been working at all I think he finally understood. It was a killer watching his face when I replaced the PS and it worked though. :D

Col

by dtaveras79

Thanks for your suggestion. I will replace the PSU and see what happens.
Come to think of it, I do see that the fan on the PSU is spinning lightly, not with much enthusiasm.

by wizard-09

The heatsink needs the fan replaced, you wont run your computer very long without the heatsink fan not working.

How long does your computer stay on for after it is turned on, does it just shut down again.

Have you checked another LCD to check if its a monitor problem or not since you already checked the Video Card

by dtaveras79

The computer stays on forever without shutting down.
The light on the Mobo turns on, the case fan spins, the PSU fan (spins lightly though) spins as well.
I have tried a working LCD monitor and I get the same message.

by dtaveras79

It's not the PSU.

I purchased a brand new 680W PSU and everything works the same way. The video card's fan spins, the case fan spins, the led lights up green on the mobo.

I guess my next step will be to purchase a brand new CPU fan???

by computercookie

though if the Video card is OK as you claim then it should POST, unless there is a PSU or MB problem.

I suggest the MB may be your problem as it would shut down very quickly if the heatsink fan was not working!

by dtaveras79

Shouldn't the heatsink fan run even if the mobo is defective. Everything else seems to be spinning. I don't think it's the PSU since I replaced it with a brand new one.
I also replaced the video card with a brand new one. And I tried two working LCD monitors and still no video signal.
Even if the heatsink fan were to be defective, I should get a few seconds of video before the computer shuts down.
Would the CPU be defective???

by oh smeg

But in answer to your questions

[i]Shouldn't the heatsink fan run even if the mobo is defective[/i]

Maybe Maybe not depending on what has failed on the M'Board. For instance if some tracks have lifted or broken then not the fan shouldn't work. Here it really depends on what has happened and if the unit was pulled out of service when it started to give problems or if it was run till it died an early unnatural death.

For instance if the CPU Fan Failed and the owner went into BIOS and switched off the Alarm and ability of the M'Board circuity to protect the CPU an then ran it till it stopped then no it shouldn't work.

However if it was pulled out of service as soon as it started giving problems then you should just be looking at what failed initially.

[i]Even if the heatsink fan were to be defective, I should get a few seconds of video before the computer shuts down. [/i]

Again this all depends on what has happened and how the unit was treated. It can also be part of the Make & Model of the CPU & M'Board here as well things like ECS which are complete junk do not offer the same level of protection that Gigabyte M'Boards do to the CPU's and RAM/

Also if this has an AMD CPU then the PS Failing would have taken out the M'Board, CPU maybe the HDD's and RAM. Just seems to be the way that things work with AMD CPU's where as a failing M'Board with an Intel CPU on it just tended to die without hurting the CPU. I'm sure that some Intel CPU's are destroyed when their M'Boards fail it's just that I haven't seen one yet. The same applies to AMD CPU's here as well I'm sure that there must be some AMD CPU's where the M'Board fails and doesn't affect the CPU but again I haven't seen an example of this yet.

Col

by dtaveras79

I replaced the heatsink fan with a brand new one and the fan works now, although I still get NO video on the monitor.

The owner couldn't have gone into the BIOS since she is not computer savvy.

by dtaveras79

OK, so it seems that the only componentleft to swap out is the MOBO.

I just tried using the CPU in question on my home computer (they have the same sockets LGA775 Socket for Intel)and it successfully booted up into Windows.

I don't see any burned capacitors on the Mobo, it's weird how it could have gone bad.

by peconet tietokoneet

Have you tried different memory chips?.
Give that a go before you replace the motherboard. I had the same with my motherboard, i took out the memory and video card and powered on for a few seconds then powered down, replaced the memory first and then the video/graphic card, it worked after that.

Please post back if you have any more problems or questions.

by dtaveras79

I tried what you suggested already and it didn't work. I tried it again this time just in case I did it wrong the first time. I'm still not getting any video.

I'm leaning on the Mobo as the culprit.

Any other suggestions?

by rob miners

to jamesmondtan's suggestion.

The monitor is not recieving any signal from the video card. If you have onboard video, try using that instead of the video card. If the card is not seated properly, then the motherboard will default to the onboard video system and no signal will be sent from the video card.

by jamesmondtan

Is the motherboard having onboard vga? If yes go to bios setting and see if the display was set to AGP or onboard. Try to use onboard vga in bios and connect the vga cable to onboard port. If it works after login to windows and install all drivers properly and restart then go to bios again change display to AGP or PCI. Hope this help.

by peconet tietokoneet

But to do that you will need to take out the bios chip and put it into another motherboard. Risky? yes but it works.
I will have to find the instructions that is on my server for you.

Ok here are the instructions:

How to hotflash your bios chip

Occasionally, either through a bad flash or corruption ie through a virus, you could be left with an unusable mobo.
One way round it is to buy a replacement bios chip, another is to Hot Flash it.

What is Hot Flashing and how do you do it?

What is it?

Hot Flashing is a way of using a running mobo with a compatible bios chip as a host for your corrupted bios chip. Your corrupted bios chip obviously won't allow you to run POST, therefore won't allow you to re-flash it normally, so you need to use another mobo to get you there.

What to do

You'll need a mobo with a compatible bios chip.
A tool to remove the bios chip
A DOS boot disc with a flashing utility and the required bios image

You'll be using a live running mobo, so extreme care should be taken!

Here's how:

The easiest way to remove the working bios chip is to remove it whilst the mobo is disconnected, then put it in just enough so that it is connected but not fully inserted.
Another method is to either attach some dental floss with a little superglue to the top of it, or run a piece of dental floss under it, so that when the ends are pulled it comes out easier.
If you have a bios removal then the above isn't necessary.

Using the working mobo, create a DOS-boot disc on a spare floppy.
Copy the bios image file for your corrupted bios chip from the manufacturer's website it usually has a .bin or .rom extension.
Most manufacturer's have a downloadable flash utility which can be copied straight to the floppy.
Make note of the orientation of the bios chip on your working mobo, one corner is angled.
Disconnect any unnecessary hardware such as Hdd's, Opticals etc. to prevent loss of data.
Set your primary boot device to Floppy, then reboot.

When the screen says "INSERT SYSTEM DISK AND HIT ENTER TO RESTART", you need to swap bios chips.
At this point the bios chip has done it's job and is no longer required, so remove it carefully and replace it with the corrupted bios chip. Make sure you orientate it correctly!

Now insert the floppy containing the bios flash utility and flash as you would normally.
When the flash is complete, remember you don't want the mobo to boot with the newly flashed bios chip in, unless it is the same mobo!
Switch off and switch bios chips, your corrupted bios chip should now be fully working, time to make sure.
Hope this helps you in getting your motherboard running.

by dtaveras79

Complicated. I tried doing this on an old Mobo and damaged the board. I wouldn't want to try this on the on my ASUS board.

Any other suggestions?

by snuffy09

Could your BIOS be defaulting to your onboard video?

I bought a new gigabyte board last month turned it on and got nothing on the monitor. I had to go in the bios and tell it to use the PCIE card

about other problems - what kinda shape is your power supply in?

by dtaveras79

Even if I did, I wouldn't be able to go into the BIOS' config...I can't see anything on the monitor.

by peconet tietokoneet

If it is new then return it,let the manufacturer deal with it. Hopefully they will give you another board that works better.

by skdtech

Not to denigrate you but have you made sure the LCDs are set to the correct input and checked the cables for broken/damaged pins and/or tried different cables.

by dtaveras79

Yes,
I have checked all of the cables. All the cables are properly inserted into their respective ports.
I spoke to someone at the company where I purchased my computer from. They told me that it might be the PCI-e slots that are defective. I also have a PCI slot on the same board and it didn't work when I put in a regular PCI video card.
I'm waiting for their reply. Hopefully I can get a new board soon.

This discussion is closed to new replies.