Question Locked

PC boots up. Red light stays on. Monitor starts up as if a normal boot up

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Yesterday I installed some RAM into my PC.

I made sure it was compatible with my Mobo, and it was the same brand as was in currently...just got more gigs.

After I installed them I got it all running properly and had it on for a few hours. Then I changed some settings for Windows and turned it off so the settings could take effect.

Now when I hit the power button, it begins to start up like normal but there is a Red light that stays on next to the green (i'm assuming its a power light.) The monitor turns on as if a normal boot up is going to take place. Before it shows any of the Windows text on the screen it completely turns itself off.

Any help please?

8 replies

by Former member

Have a look at your hdd, un-plug it and re-apply the cable then take out your new ram and re-seat them into another socket. When finished go into the bios and select "load default settings", press the "F10" key on your keyboard and confirm by pressing "Y" (for yes). Your computer should now boot-up normally.

Please post back if you have any more problems or questions.

by nepenthe0

Tap F8 after powering on the PC to boot in Safe Mode. Highlight [i]last good configuration[/i] and hit [i]Enter[/i].

This should restore your PC to a working configuration.

Before you make any further settings changes, be sure to create a [i]restore[/i] point in System Restore.

Hope this works. Please post back in this thread if problems persist.

Rick/Portland, OR

by xiviergaming

My computer cannot even get to a point where I can hit F8 or anything of that sort.

I have unplugged my hard drive and reseated all my ram.

Problem persists.

by nepenthe0

If you have a Windows installation CD, you can reinstall Windows in [i]repair[/i] mode.

If you have a bundled OEM installation CD, you should likewise have an option to [i]repair[/i] all drivers.

If you can boot from the installation CD, your hardware should be OK. If you cannot boot from the installation CD, things aren't looking very promising. Hard drives do croak, often without warning.

You may be able to run a HD diagnostic program from a CD such as the Seagate utility:

http://www.seagate.com/www/en-us/support/downloads/seatools/

Sorry I couldn't be of more help.

Rick/Portland, OR

by xiviergaming

I put in my XP cd...nothing.

I did have a bundle disk for my dvd rom I had from when I got it...tried it and nothing.

Same thing happens over and over.

by nepenthe0

A general principle of troubleshooting is to restore the configuration when the machine was working OK. If it still works OK, then the change you made caused the mischief.

If the only change you made was the installation of new memory chips, I recommend restoring the original chips. If that solves the problem, your new RAM chips are the culprit, either flawed or incompatible.

Rick/Portland, OR

by rob miners

A common reason for shutting down and locking up or freezing is the CPU overheating.

Faulty Fans, Dust and Grime build up on the Heatsink restricting air flow. I would give the inside of the case a blowout with compressed air. When blowing air through the fans make sure that you physically stop them from spinning, as they may generate power and blow something up. Then remove the Heatsink, giving it a thorough clean and reseat the CPU applying new CPU grease. If the Fans spin freely when you give them a spin they are probably OK. If there is resistance replace them.

Clean the golden edge of each memory stick with a soft rubber, remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC, of the original RAM

Also check Capacitors around the CPU for swelling or bulging.

A faulty PSU can also cause it. Fluctuating power is no good for the motherboard. Try another one if available or replace it.

This discussion is closed to new replies.