Question Locked

Prblem: no format, do you wish to format? har drive

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a western digital 500 GB HD the problem stated last week, I cannot access my information, there is a lot!. The drive appears in my computer but when I try to open it says that there disk is not formatted and if I wish to format the drive. I have try the WD diagnostics and it say nothing is wrong.
I have been looking in the internet and a lot of places tell me to format the drive and then buy software to recover the information.
I have the information in there should I format the drive?
What I can do to recover the files?
Is there a way I can fix so I do not have to format the drive?

Thanks

Jose

9 replies

by scott_heath

The Windows Disk Management utility say about the drive? Did you do anything like convert it to dynamic, encrypt it, resixe a partition, etc...?

by nquique

Disk 1
Basic
465.76 GB
Online

(E:)
465.76
Healthy

I didn?t do anything to the disk, I turn it off without disconnecting first.

by scott_heath

Do not format. Try a trial data recovery tool to see what you can get back. I like Ontrack's Easy Recovery Pro and have used it numerous times in the past to recover data.

by willcomp

Do not format the drive.

Am I correct in assuming that this is an external USB drive?

by nquique

Yes is a external hard drive, is USB, Is My Book Home edition, 500 GB,

by willcomp

You may need to attach drive to an internal SATA or IDE connector, but give GetDataBack a try first. It has a free trial.
http://www.runtime.org/

Apparently XP is trying to access disk in RAW mode. Your data is probably still intact.

by oh smeg

To turn off the USB drive by using the Safely Remove Option on the Start Bar.

I do not like the idea of formating the drive as the chances of loosing data are too great but some of the available software that can be used to recover your data is expensive and some Data Recovery Programs require a Formatted HDD to work from.

When doing any Data Recovery Work [b]Never Write anything to the Affected Drive[/b] You run the risk of overwriting your data and making it very hard to recover and expensive as well.

There are several options available to you here and you can use any of these Software packages. I can only talk for the On Track offering as it is the only one that I use but it's also the most expensive so another package may suit your needs better.

I have heard good reports about all of these packages so look at them all and chose one that suits your needs and experience level.

The list is in not order except the way that it is stored in my Bookmarks so please look at everything listed.

http://tinyurl.com/pfuhz

http://tinyurl.com/6j8xa

http://tinyurl.com/273ay5

http://tinyurl.com/afu2j

http://tinyurl.com/rmvrv

http://tinyurl.com/yvrsl

http://tinyurl.com/yyk8cm

http://tinyurl.com/382vm

http://tinyurl.com/3bb2t2

http://tinyurl.com/374d8b

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

http://www.x-ways.net/winhex/

The last listing for Win Hex should only be used if you are very experienced and know Hex inside out. If you do not know Hex [b]Do Not[/b] touch Win Hex as you are far more likely to do more damage that you can fix. This is a very powerful tool that needs to be used with caution.

Col

by mayhem1969

I have seen where XP will give this message if it is not updated to SP2, because while it sees the drive it doesn't recognize the partition or the files on it and asks for a format, thinking its a new drive. As mentioned, do not format.

Also if its Vista, make sure you have the latest drivers for that device loaded.

This discussion is closed to new replies.