Question Locked

Problem getting data off old hard drive using an enclosure

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Just purchased an enclosure to try and get the data off my old laptop's hard drive (used to run XP, but now won't boot) onto my other laptop running vista. So The new laptop recognises the hard drive but rather than saying it's got so many GB's out of 80GB free it says 3.77Mb of 10.1MB has been used (in 'my computer'). In disk management it says that the drive is 75GB, as expected. When I try to view what's on the hard drive there's a load of folders that can't be opened and some files that can't be opened.

Any help would be much appreciated.

10 replies

by oh smeg

Doesn't matter if you can open the folders or not just if what should be present is.

If that is OK then you need to take Ownership of the Files & Folders because you had a Password involved when you opened Windows and these Files & Folders where marked as Private. With XP the process is posted here though I'm not sure that it works when there is Vista Involved.

http://support.microsoft.com/default.aspx?scid=kb;en-us;308421

Also if you where using EFS under XP this is not supported by Vista so you'll need to find another computer running XP to remove the Encryption as the files will remain unreadable otherwise. You'll probably need to read this item about Mounting the EFS Recovery Agent under XP.

http://support.microsoft.com/kb/887414/en-us

Col

by jamesherbie

Unfortunately they're not the files and folders I want. They all have strange names like[.str. Whereas I basically just want to get hold of my pictures and my documents.

by oh smeg

Several computers particularly IBM Think Pads have a security Chip included on the M'Board which basically encrypts the entire HDD.

To get to the Data on these you need the same model computer. :)

Col

by jamesherbie

It was a Compaq, the computer I'm trying to get the data to is a Dell.

by oh smeg

Not the C Partition.

Can you plug it into another XP Computer and see what happens here? Sometimes the NTFS Partitions made under XP particular if it is a Pre SP1 XP are not readable by Vista owing to the different Security Protocols. When this happens the drive remains Blank and is only seen as a [b]Mass Storage Device[/b] which is the interface Card in the Enclosure that the HDD plugs into. If you add a FAT32 Partition to the Mix like those used in NB's you would only be able to see the FAT 32 Partition.

Doesn't matter which version of XP you where running if the Partition was made by a Pre SP1 Version the Format or MBR's are not supported by Vista. When you apply SP1 or latter this doesn't affect the Partition's of the HDD. :)

Col

by jamesherbie

I got my old XP Desktop working again (running service pack 1) - not connected to the internet.

I connected the enclosure with the HD inside to the PC, came up as a local disk. However when you view the files from my computer you just get the same unopenable files and folders.

If you try and open the folders you get the message - ...refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure disk is properly inserted, or that you are connected to the internet or your network, and then try again. If it still cannot be located the information might have been moved to a different location.

Clicking on properties (from my computer) says 6.72MB used space, 3.37MB free sapce, 10.1MB capacity, type: Local Disk, file system: FAT.

Going to device manager>>disk drives it says type: basic, status: online, Partition style: Master Boot Record (MBR), capacity: 76317MB, Unallocated space; 0MB (in vista this says 1MB), Reserved space; 0MB. Then underneath this it agains says the capacity of the volume is 10MB.

by oh smeg

Remove the HDD from the Enclosure and look at the Pins where it plugs in.

Are there 2 rows of Pins here or two Plugs that are in use?

If there are 2 rows of pins, is there a Plastic Jumper shorting 2 Pins out in use here?

If there is Remove it and refit it to the enclosure and see if it is readable now.

If that makes no difference look at the Jumper Setting on the HDD and refit the Jumper so that the drive is set to Master and try again.

If there are two plugs this is a SATA Type HDD and it has failed.

Post back with the results.

Col

by jamesherbie

Ok so it's got two rows of pins, in two blocks. 43 pins in one block, then another 4. There's a jumper shorting 2 of the pins.

I've tried every possibe position for the jumper (5 including removing it completely), but it makes no difference. The drive still shows 3.77/10.1MB in 'my computer' and 70 odd GB in device manager. I've tried it on both Vista and XP but it makes no difference.

by oh smeg

Is download the HDD Makers Testing Utility and test the HDD for correct function.

http://www.tacktech.com/display.cfm?ttid=287

You should test this fitted in a Computer rather than in a USB Enclosure. If it fails the first test try it in another system if it still fails the HDD is Toast and has gone to [b]Silicon Heaven[/b] however if it passes the second test the IDE Controller or Data Lead or Power Supply is shot in the original computer. :)

Col

This discussion is closed to new replies.