Question Locked

pulling info from a dead harddrive

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a dead sata harddrive, that is it runs but for some reason it wouldn't reload windows or recover my info.Anyway i put a new one in my laptop and was wondering is there anyway to get some info from that drive.

21 replies

by .martin.

corruption dead, or physical read head banging off platters?

if the first try SpinRite, at http://www.grc.com/sr/spinrite.htm it will cost you $90 (US) but it is worth it

NOTE: I do not currently, or ever have, worked for GRC, just a happy customer :)

by oh smeg

Just a Failing HDD and provided that there is no Data on the Affected damaged areas of the Platters you should be able to recover everything.

Just plug in and copy off the Data you don't need to do anything else.

Col

by oh smeg

Slip it into a USB Enclosure and connect to the computer as this is a NB use 2 USB ports to plug it i so that there is sufficient power to run the drive.

http://www.satasite.com/sata-usb-drive-enclosure-sata-ide.htm

If you had any form of security on the system before you'll probably need to Take Ownership of the files so you can access them

http://support.microsoft.com/default.aspx?scid=kb;en-us;308421

Here if you have more than NB Drives you can use a 3.5 Inch SATA Enclosure and as these have their own power supply you will not need to worry about power issues not being sufficient to run a HDD. The connectors for SATA Drives are the same on 2.5 & 3.5 inch drives.

If the drive isn't working in a USB Enclosure and you desperately need to recover the data off it send it to a Data Recovery House. This however is not Cheap.

Col

by roc_a_chic

Put the HDD in a water proof pack in your deep freezer overnight then try looking for a desktop with SATA cables to enslave it and copy off your info because the OS may not run

by oh smeg

There are several possibilities but they all revolve around the cold making parts smaller and less likely to Bind. Be that the Motor Bearings, The Distant between the Read Write Heads and the Platters or whatever. It does work but only when you can not read the drive initially some times.

If the drive is running and able to be read it's not necessary . It's always a Last Resort as well.

I used that trick while On Site once with some Dry Ice but that was a Bad Case of things going so far wrong it wasn't funny.

Col

by rev.id

hey guys,would my desktop have a sata slot along with whatever my harddrive that is in there now?If it do is it just a matter of plugging it in and windows reconizing it as another storage device?My desktop is xp and the dead hardrive is vista.

by oh smeg

Depends on just how old the system is and who made it.

New Systems should have SATA Connectors on the M'Board at least but there maybe not be any Power Connectors. You may need to use a IDE to SATA Power Converter and you would need a spare SATA Data Lead. Depending on what is actually inside your Desktop you may also need a Power Splitter to give you extra Power Plugs. As well as a new Power Supply if you have one of the more common Off the Shelf Systems.

Col

by rev.id

ok guys bought a sata to usb cord with power supply.Is it as simple as to hook it up and the computer reconizes the drive,then going in on it and extracting the files I want.Another question,if the windows files are corrupt and wont reload can I use the drive for storage,since I bought the cables and everything?

by rev.id

ok its not dead but i couldn't do anything with it,windows wouldn't even start or run so I installed another harddrive.So iam hoping I can recover some info of the drive.I've been told to get a sata to usb cable and hook it up to my desktop system and run some kinda recovery software.If i run this iam hoping to get the option of picking where i can pull the info from.Some software will only pull from the usual locations,ie:my documents.I downloaded a program called minipe but theres alot of smaller programs within and don't know which to use .Are you famaliar with this program?thanks

by oh smeg

Because the drive is actually working even if it doesn't boot that only means that the Windows Files are corrupt.

What you need to do here is connect it to t Computer and I would do this through a USB To SATA Connector and that would generally be an External HDD Enclosure but in this case you can fit it to a computer as a Slave drive and when you boot windows off another HDD you can open this drive through Explorer, My Computer or whatever you like.

The only draw back with fitting it as a Slave is if you do not have any SATA Drives installed you'll need to install the SATA Driver so you can access this drive.

The other thing you may have to do is to [b]Take Ownership of your Files[/b] by following the direction shere

http://support.microsoft.com/default.aspx?scid=kb;en-us;308421

Col

by oh smeg

Though if you had a Password on the Old System you will need to Take Ownership of the Files & Folders to be able to access them.

As for your Second Question the answer is [b]Yes you can.[/b] Though it wold be a better Idea to First get all your Data Off this Drive then to Format it under the working OS and then copy all your Data back to it. That way you will not have any unnecessary Files taking up space that you don't need there and have all of the possible room available to Backup Data to.

You should however be aware that these are not for [b]Full Time[/b] use you should only run a HDD like this when it is needed and not leave it running all of the time. If you do the Drive will suffer both Heat & Vibrational Damage and have a considerably shorter life than it should.

Col

by rev.id

hey guys,bought a sata hookup for that hardrive,hooked it up to my desktop but it don't even reconize it.My desktop runs xp and the hardrive is vista so I hooked it up to my laptop via the usb that came with the hookup kit and still no go.It spins but my laptop don't reconize that its there,all i get is a new hardware icon but thats it.Am I missing something or doing something wrong?thanks

by oh smeg

To see if the drive gets listed there?

If it does either there is a conflict with the associated Drive Letter in which case you can change the drive letter to gain access tot he drive again.

Or this drive has been removed without using the Safely remove Option and this includes turning off the computer with the drive plugged in and running so the Partition Information has been corrupted.

Or the actual HDD's Circuit Board has failed. If it's the last you can get another Identical HDD and swap the Circuit Boards to recover your Data though you will need a suitable Torx Driver to do this.

If it is the fact that the drive has not been shut down correctly and you need to recover the Data on it this is where things get difficult. If this is [b]Important Data that Must Be Recovered[/b] send the drive to a Data Recovery Specialist. However if it would just be [b]Nice[/b] to recover this Data you can attack the drive with a Data Recovery Application. Though before proceeding any further you need to make sure that the drive is actually working correctly so test it with the Drive Makers Testing Utility available here, just click on the Drive Makers Name and you will be prompted to download the correct File.

http://www.tacktech.com/display.cfm?ttid=287

However if the Partition Information has been corrupted you need a Recovery Program that can rebuild this Data. There are two types of Data Recovery Application one will recovery Individual Files, Types or whatever and the other rebuilds the Partition Tables. Here is a short list of the better ones but it is by no means a complete list of all the available software.

http://tinyurl.com/273ay5

http://tinyurl.com/rmvrv

http://tinyurl.com/yvrsl

http://tinyurl.com/yyk8cm

http://tinyurl.com/382vm

http://tinyurl.com/ynwnel

http://tinyurl.com/nc4kx

http://tinyurl.com/2wox7l

http://tinyurl.com/374d8b

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

http://tinyurl.com/8bd3f

http://tinyurl.com/afu2j

While the last 2 are from the same company they are very different products. Win Hex should only be considered for use by someone who knows Hex Inside Out while Davory is a great cheap General Purpose Application.

Personally I prefer the On Track Option but it's anything but cheap. However because I use this type of software a lot it's paid for itself many times over by now, for a cheaper option Spin Rite from Gibson Research or Stella have both very good reputations by other TR members.

Col

by rev.id

wow thanks for all the info there guys.so lets see if I got this straight:hook up the bad hardrive,start laptop ,then run program to check hardrive.Does it matter if its a sata drive,i mean if its a maxtor sata I have to find a utility to scan a sata drive and not an ide drive?

by oh smeg

If it is through a USB Connection you should start the NB first then plug in the HDD.

Otherwise everything is as you asked. :(

Col

by rev.id

Thanks OH. Iam hooking up usb with its own power supply. Its a cable hookup - bought seperately. The last time I tried my NB showed new hardware hooked up but it never showed up in explorer.no letter assigned just the fact that there was hardware there. How do I go about getting my NB to see what actually is there?the bad harddrive is spinning but that's it. Thanks for the info.

by oh smeg

The HDD itself is either not reading the Data on the Platters or it Partition information may be corrupt.

Look in Drive Management and see if the drive appears there but if there is any [b]Important[/b] Data on this HDD it would be better to send directly to a Data Recovery Specialist. However if the Data on the Drive would only be [b]Nice[/b] to recover you can try one of these. ;)

Here is a short list of the better ones but it is by no means a complete list of all the available software.

http://tinyurl.com/273ay5

http://tinyurl.com/rmvrv

http://tinyurl.com/yvrsl

http://tinyurl.com/yyk8cm

http://tinyurl.com/382vm

http://tinyurl.com/ynwnel

http://tinyurl.com/nc4kx

http://tinyurl.com/2wox7l

http://tinyurl.com/374d8b

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

http://tinyurl.com/8bd3f

http://tinyurl.com/afu2j

While the last 2 are from the same company they are very different products. Win Hex should only be considered for use by someone who knows Hex Inside Out while Davory is a great cheap General Purpose Application.

Personally I prefer the On Track Option but it's anything but cheap. However because I use this type of software a lot it's paid for itself many times over by now, for a cheaper option Spin Rite from Gibson Research or Stella have both very good reputations by other TR members.

Col

This discussion is closed to new replies.