Question Locked

Putting 'recovery partition' on new laptop hard drive . . .

0 helpful
31 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My personal Acer laptop - 2.5 yrs old - with a pre-installed Windows XP Home.

The HDD has a restore partition (I:\) from which I have re-installed twice (once due to my own 'gung-ho' stupidity and more recently due to a start-up system crash.

The laptop has a TSST L-532A slimline DVD-Dual drive which presented with problems within 6 months of use. After one warranty replacement it died again (just outside warranty cover!) and I never replaced it, opting to network the Acer with my old Tower unit, using the tower to install to the laptop whenever required.

-------------
End of preamble!
-------------

The primary boot partition is showing signs of imminent demise (read errors, slow loading, stalling, inability to return from hibernation) and it is sensible to assume that after two and a half years the hard drive has seen a reasonable life ~including P2P transfers~ and should be replaced forthwith.

[b]PROBLEM![/b]

Since my only means of re-install is from the 'recovery partition' (which is part of the existing hard drive); HOW can I put said partition onto a NEW hard drive ????

I've experienced situations where the recovery partition was in fact a Ghost image, and if the 'new' hard drive did not PERFECTLY copy the old drive, then the 'recovery' partition would not perform properly.

Replacing the hard drive is not a problem but losing my installation is!

I'll copy the entire partition onto my tower for future use on the Acer - BUT - any thoughts on whether I can replace the existing HDD with a larger HDD or am I forced to replace with the same total volume capacity ??

I'VE HAD PLENTY OF TIME TO THINK ABOUT THIS - BUT NOW I'VE GOT TO DO IT!

Thoughts please - the more the merrier (Chrimbo spirit and all that!)

31 replies

by rob miners

Don't lose the old drive just yet. Can you access the hidden partition? Is there an I386 folder in there or an image? If you refer back to injecting updates you will know where I am coming from.

by older mycroft

I've got some idea - but can you be a bit more specific?

It's the age-old thing ~ when it's someone-else's machine I am totally focussed but when it's my www.lifeline I begin to panic!

Eventually [u]this[/u] drive will fail and my link with TR will also die!

Simple - but true... :(

by rob miners

I was referring to a question that you asked awhile back. If the I: contains a folder I386 that is all that you will need to rebuild. Unfortunately you would lose the Recovery Partition but you will still be able to install. If there is an Image you may be able to install it from CD. But in the meantime I have found some valuable info that was not available to me when I was playing with recovery partitions. I will post a couple of links for you to perouse. It looks as though you can change the partition type with PARTEDIT32. You may have to play a bit but if you can Ghost the Recovery Partition to your new Drive you may be in business. There is a reference to creating 3 Partitions and getting them to the right size. So it looks like you have to copy at least the Recovery partition and the Data Partition which is I:
Anyway have a read and keep posting.

http://ezinearticles.com/?The-Most-Simplest-Way-To-Unhide-A-Hidden-Partition&id=497809

http://ezinearticles.com/?How-to-Repair-the-Acer-D2D-Recovery&id=794500

http://laptop-support.net/

by rob miners

I have an Acer with a Recovery Partition. I am going to have a play er experiment.

by rob miners

This expriment is very interesting. I am also limited to using a smaller capacity HD as the new Drive only 20GB. Using an Acer Extensa 2300 that was given to me for Spare Parts with a 40GB Drive. Ptedit32 will not allow me to change the Partition to 0c nor will Ranish Partition Manager. I tried to copy it with Ghost 7 and it could only do a sector by sector but it did copy it. Prepared the new drive by creating 2 Primary Partitions the first ones size was 3074 and converted to type 12 with Ranish. The second Partition was left with the remainder of the drive and left as 0c. The option to drop the boot image in ghost was greyed out. Error message to do with mfr? on the target. Tried the same with Acronis 9 it copied the boot image and restored it. Unforunatly it is looking for a command interpreter so it isn't bootable. Eventually copied it with Cute Partition Manager. Still no Command interpreter so I changed the Partition type to 0C and installed DOS7.

Rebooted and ran D2D.exe. I was able to install the OS but I have no Recovery access anymore. So I have had no luck whatsoever with the Recovery Partition apart fom being able to install the OS. The Recovery Partition contains Ghost password protected images. It has a modified Command.com as well. Interesting that not one of the 3 Imaging Tools that I used was able to set the Volume Label or do a complete copy of that Partition with the System intact. I didn't try DD as Pond Scum suggested as I was unsure of the commands needed to just copy the Recovery Partition. I am not very familiar with Linux or which version to use as there are so many.

Reset the new drive up with one partition. I had previously Ghosted the OS to an image with Ghost 7. Dropped the image to the new drive and it is up and running after an initial restart. I then used Acronis 9 to create a Recovery-Backup Partition and then Backed up the Drive. I only have to press F11 on startup and recover from the backup. Restored the Drive from Recovery to test and everything worked well.

If you think that your poor old drive could take it I would Ghost the OS Partition after a good cleanup. Backup everything of value and do a Rebuild so that everything is fresh and Ghost it again to give you an original copy. Whats that old saying to be sure to be sure.

Don't forget to do the pagefile mod to turn off on shutdown to save a bit of space. Local Security Settings, Local Policies, Security Options, Shutdown: Clear virtual memory pagefile.

I don't know if any of this will be of use to you but I now have a Complete Backup of a Fresh Install. If my Drive fails I can just ReImage the New Drive.
Edit:
I forgot to add that my problems may have been caused by the fact that the Drive with the Recovery Partition is a Seagate and my "New Drive" is a Fujitsu. As I said I am limited as to what I may achieve.

by older mycroft

The thing is - from what I've read in the computer press lately, it seems that junless the new drive is an exact copy (in terms of total capacity) then the 'ghosted Acer recovery partition won't work, because it won't 'see' what it is expecting to be there.

NOW: this has confused me since each time I used the recovery partition the re-install only went as far as the C:\ partition, leaving the D:\ partition alone.

After the first implementation of the re-install I created new paths for all my document files, to re-path them onto the D:\ partition, so that the next re-install didn't leave me with a totally blank factory-fitted system (all trinket files like oggs, mp3s, jpgs etc are 'safe' on the D:\ partition.

But if you've managed the process with a drastically reduced total capacity drive then maybe what I've been reading has all just been nonsense.

I was hoping to max out on a replacement hard drive, maybe as much as 160GB.

by older mycroft

These are articles I've never come across before - SPOT-ON-mate !! :D

by ic-it

MHDD I have had good results by allowing this program scan and repair the drive. Usually you will want to set it to loop and remap. It isn't very intuitive but basically you choose the drive, press F4, use the arrow keys to scroll and the space bar to change options, F4 starts the scan after selecting the options. Set Remap to ON. Set Loop/repair to ON. Let it run through at least three times.
The program can be found from the link below or with the UBCD ISO.

http://hddguru.com/content/en/software/2005.10.02-MHDD/

by older mycroft

. . . .THAT [u]firstborn[/u] will ever end up with your name!) :D

Ooops - forgot - private joke!
You just gotta follow the threads!

by sue t

Why not just make an image of it or I know Seagate has tools that you can connect the new hard drive and have it imaged from the current one. This just seems a lot easier. I would still make an image of the recovery partition though if you can.

by older mycroft

actually in-place on the laptop itself?

Beginning to think I've made a rod for my own back by networking rather than replacing the laptop optical drive!

by willcomp

Hook old and new drives up to a desktop PC and image partition there. You can use USB enclosures or notebook drive IDE converter.

by sue t

have a floppy drive or do you have an external one? Does your desktop have an optical drive? If it does you could remove it from the tower and use an adapter to connect it to a USB port on the laptop. I would probably connect my external floppy drive to a usb port on the laptop and also connect the new hard drive to the laptop using an adapter.

by rob miners

I use a standard PC and a Laptop IDE Hard Drive Adaptor. 40GB Drive formatted FAT32 set as Slave for the images. If you haven't got one get one they are about 10 aussie dollars. I also have a USB adaptor that is fine for the smaller capacity drives but without a power connector it will not power up the larger capacity drives.

A picture for you OldMycroft.

http://www.datapro.net/products/laptop-ide-hard-drive-adaptor.html

by the scummy one

Lots of good answers so far.
Now, here is one that is not mentioned, but it is limited a bit.
DD command in Linux is a bit by bit drive clone, which can do partitions or whole HDD's.

The easiest way, would be to boot to Linux and slave the new HDD as a USB drive. Mount the main drive and then type from a prompt

dd if=hda of=sda
This should clone all mounted partitions from the HDD and write it to the USB drive.

I once used this to clone a running Linux machine (being used for several tasks) to a USB drive. then I replaced the USB drive as the main drive and it worked flawlessly (after the first reboot to clear the swap partition)

by Former member

In the past when I have had a hard disk failure, I have sealed the computer, or hard disk, in a plastic bag a placed it in the freezer for several hours. It won't cure the drive, but it can give you just enough life to image from it.

by cg it

I get a laptop HDD IDE converter and plug the laptop HDD in to my desktop as a slave HDD.

http://www.cablesnmor.com/hard-drive-converter.html

Then I copy the contents to an external HDD.

I make an image if I can.

Once I get a new HDD with ample space, reimage. If that doesn't work, then I install a fresh copy of the O/S, then move the contents of the old drive to the new drive.

by cg it

they do come with power adapters.

by rob miners

that it has to do with the drive if I had another Seagate it probably would have worked. I don't think that the capacity should matter if the Drives are from the same manufacturer. If you rebuild from the Recovery it only seems to be concerned with C: Drive and the OS. I didn't bother recreating D: drive as I was limited. The rebuild didn't seem to mind that it wasn't availabe. If you can setup the Recovery Partition on the New Drive exactly the same size as the old one then create a second primary Partition the size that you want and then create your Logical Partition with what is left it may work. If you decide to just Ghost the OS, you can set the Drive up as you like. The D: partition was probably part of the old setup where it was originally the Recovery area to create CD's or your DVD for the OS.

by rob miners

only has power for Sata and IDE it dosen't have the little connector like the 2.5 to IDE adaptor. That link is a model similar to mine. I wasn't able to find the same type.

by cg it

the 2.5 laptops HDDs that aren't SATA are IDE. Often the power connectors are built in to the HHD with the 40pin data connector.

the kits have this 40pin data connector & a 4 pin power connector all on one PCB board so you can plug in to a desktop 40pin IDE cable and also a 4 pin power supply connector.

There's many distributors that carry these things. TigerDirect, Newegg.com blah blah.

by rob miners

its the way I try to explain things. I can think it and talk it but when I try to write it, it does't always come out right.

These are the two types that I use. Unfortunately the first one only provides power for Sata and IDE. I prefer to use the second one as it is a lot faster to access the drive and comes with a power connector. The only drawback is that you have to remove the cover to connect it. I mainly use the first one for Backup. Comes in very handy sometimes.

1. USB 2.0 to IDE / SATA Adapter Cable 80cm (Supports 2.5" & 3.5" IDE)

http://tinyurl.com/36uql7

2. Laptop IDE Hard Drive Adaptor

http://www.datapro.net/products/laptop-ide-hard-drive-adaptor.html

by older mycroft

If you just got another Thumb - you know who you are, Willcomp !! ;)

by rob miners

that other posters don't follow suit. :)

The amount of questions that have been answerd correctly far outweigh the amount of thumbs awarded. :)

And it's not only my posts. :)

by older mycroft

There wasn't much happening so I had a trip down memory lane. :)

AND you're correct - it's not just your posts! ;)

This discussion is closed to new replies.