Question Locked

RAW hard drive issue

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Hi everybody. I have recently bought a Nexstar 3.0 USB 2.0 hard drive enclosure case in order to install my old 3.5" hard drive. After everything is installed, I connected it with my IBM laptop, but the disk management shows me it's a RAW type drive. Then I used the software "Data Recovery" to scan my drives. The scanning result is my USB hard drive is NTFS type. Why the system does not recognize it? Is there any way to solve?Thanks!

14 replies

by peconet tietokoneet

You might need to format it and give it a letter. You can do this through "disk management".

Please post back if you have any more problems or questions.

by oh smeg

Make sure that the external Power Adapter is plugged into a working power socket and check the jumpering on the Drive.

It should be on Master not Cable Select or Slave.

Col

by hippo007003

Thanks for your reply. This USB hard drive enclosure case does have a power adapter and I have plugged in a regular socket. The flash light on this case should be flashing all the time if the system is synchronizing it; however, the flash light does not flash. This old hard drive was used as a Master drive in my old desktop. May it be the problem?

by oh smeg

It still could have been set to CS or Cable Select.

When you add them to a USB Enclosure you need to set them to Master. CS [b]Will Not[/b] work.

Also while this will not have any effect on how the system recognizes the USB HDD what OS' where in use previously? If one was an old version of XP Updated over the years and the new one is Vista the Partition Information may not be usable with the New Computer as the Security Systems on the 2 Versions of Windows is different and you can not read a old XP Created Partition on Vista without reformatting.

If that is the case you will need to use a XP System to read the Data on the HDD and save it elsewhere before you can format the drive under Vista and use it with the new computer.

You should look in the Disc Management Windows to see what the OS is seeing this HDD as too Not rely on software that may actually corrupt the Data. :)

Col

by rob miners

in the enclosure especially the power connector as it may not be fully inserted. Try another power outlet to plug the enclosure into.

{1}

Try rebooting the computer without any USB devices attached. Then plug in the USB drive, right click on My Computer, select manage, and then click ?Disk Management.? If the drive is not present in the Disk Management window or if you are not able to access it, then the drive may have failed. In this window you should see all of your connected physical drives, their format, if they are healthy, and the drive letter.

Change the drive letter of the drive. Right-click on the drive in the list, and from the resulting menu select "Change Drive Letters and Paths"

Click on Change so you can change the drive letter. Click Change. Select a new drive letter from the drop down list, preferably the one that is not normally used for this drive.

Click Yes on the confirmation screen and you are done.

{2}

Write down all fixed Disk and CD/DVD drive letters so as not to delete them. DO NOT delete any of the fixed hard disk drives or CD/DVD optical drives registry values.

1. Login with Administrative privileges.

2. Disconnect all USB or FireWire storage devices.

3. Open Registry Editor by typing regedt32 in the Run box and navigate to the following registry key: HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices

4. Under HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices there will be registry keys with the name that resembles the format of \DosDevice\X: where X can be any alphabet letter which corresponding to your physical system drive letter.

5. Delete all possible USB drives, FireWire drives and external drives which have a drive letter.

DO NOT delete any of the fixed Hard Disk Drives or CD/DVD optical drives registry values.

Exclude \DosDevice\A: which normally reserved for floppy disk drives.

by hippo007003

Hi my friend. I have just adjusted my jumper to the Master location, but the system still could not recognize it. Anyway, then I replaced it with another old hard drive. After installation, I have connected it to my laptop and the system found it and displayed for 4 partitions such as F: G: H: I:. They all can be opened normally. I want to find why my previous old hard drive cannot work but this one can. Then I went to the disk management and I click choose F: drive, and the status is healthy and active. Ah...very good! Then I right clicked it and delete the partition, and I added the partition back, but this time the F: drive is forever gone. I couldn't open it and it needs me to format it now:) This situation is very similar to my previous old hard drive because I did partition when I connected it at the 1st time when the system didn't find it. I thought it was the system problem,but actually it was the jumper problem; however, I have partitioned it mistakenly and then I can never make the system recognize it. Any other way to get it back for this mistake?

by hippo007003

Hi there. What do u mean about OS? How to set my HDD to Master?

by seanferd

in your case, XP of some version with whatever service pack (sp).

Set HDD to master-
You'll have to pull the drive, and look at the back end. There are sets of small pins back there that are used to achieve this. There should be a little rectangular jumper connecting two of them. The jumper need to be on the pins that set your drive as a master (sometimes this means no jumper on the pins). The sets of pins may be marked, or they may not be. the markings would be something like MS=master, CS= cable select, SL=slave. If not marked, check the manufacturers website for your exact model, or refer to any disk or booklet that came with the drive.

by oh smeg

The First if the Data is Important is to take it to a Data Recovery House and pay them to recover your Data.

The Second is to throw some sort of Data Recovery Program at it and try to recover the Drive. If it is Important don't mes with it as it will end up costing you more with a lower chance of recovering any Data.

Here is a short list of the better ones but it is by no means a complete list of all the available software.

http://tinyurl.com/273ay5

http://tinyurl.com/rmvrv

http://tinyurl.com/yvrsl

http://tinyurl.com/yyk8cm

http://tinyurl.com/382vm

http://tinyurl.com/ynwnel

http://tinyurl.com/nc4kx

http://tinyurl.com/2wox7l

http://tinyurl.com/374d8b

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

http://tinyurl.com/8bd3f

http://tinyurl.com/afu2j

While the last 2 are from the same company they are very different products. Win Hex should only be considered for use by someone who knows Hex Inside Out while Davory is a great cheap General Purpose Application.

Personally I prefer the On Track Option but it's anything but cheap. However because I use this type of software a lot it's paid for itself many times over by now, for a cheaper option Spin Rite from Gibson Research or Stella have both very good reputations by other TR members.

Col

This discussion is closed to new replies.