Question Locked

Retrieving data from crashed PC HDD with Compaq Presario M2000 Laptop

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello, my old Compaq Desktop PC will not boot up and I want to retrieve data from the hard drive. So I removed the PC HDD and plugged it into the jumper, and then I opened up the M2000 laptop, but it does not have a 40-pin IDE connector. The laptop connectors look like interlocking fingers with ridges, instead of pins. Is there another hard drive jumper I could use with this laptop?

Also how do I set the laptop as master?

Thanks,
Anna

6 replies

by hal 9000

A USB Caddy and then plug that into the NB and read the data off the USB External HDD. If you are running XP there will be no problems in reading the data and doing a direct copy to the new HDD in your NB.

Now is a good time to start backing up all your data as it's valuable even if the computer that it's loaded into isn't. I've had customers pay up to 50K to recover data off a $80.00 HDD because they thought that it wasn't important and that they could replace the computer when it broke.

If you had 98 Loaded on the Desktop you'll be able to directly read the data and copy it to your NB but if you had XP in any form installed and used some security you'll need to follow some basic steps to recover your data.

Firstly if you marked your user account as Private you'll need to take ownership of the files by following the directions here

http://tinyurl.com/3aw7

If you where using any Encryption you'll need to save the Encryption Key from the Old HDD and copy it into the new System so that you can save your data in a readable format. If you where using Windows Encrypted File System or EFS the directions to save a copy of the Key is here

http://tinyurl.com/orpmf

If you where using a different File Encryption System you'll need to look up the proper directions supplied by the maker of the software to recover your data.

You also don't need to set the HDD as the Master as that would be counter productive as the hardware is all changed so it will not be able to load the OS with the correct drivers on the M2000 so it's better to keep it as a Slave Drive and copy off that. If you absolutely want to use the Old HDD as the Master Drive you can set the BIOS to boot from an external HDD and then you'll need to perform an In place Install of Windows to allow it to work on the new hardware and if you have encrypted your files you'll wipe away the encryption key at the same time and loose access to all your data.

It's much easier to recover your data with the drive used as a Slave Drive or an external Drive that isn't needed to allow the computer to boot from.

If you had of mentioned the OS's that are in use on each system and what if any security you used to protect your data it would be much easier to answer your question.

The NB's HDD will always be the Master drive unless you mess with the BIOS and make the NB boot from an external HDD or other data source.

Col

by anna

So how do I know whether to get a 2.5 or 3.5 USB caddy? And the OS system on these 3 old PC's are unknown until I get into them...The owner does not remember or never knew. Maybe 98.

Thanks,
Anna

by tig2

If you have a handy anti static bag, drop the HDD into it and go visit your favourite geek superstore.

As HAL suggests, make the HDD a slave, not master. Especially as you do not know the OS. Safer that way for the reasons he points out.

Worst case- find a place that will do a file conversion for you. You can have the actual data files pulled onto a CD or DVD for a price. Realistically, they won't do anything for you that you cannot do for yourself with a hardshell HDD carrier.

The best of luck to you!

by avellve

you must have a 2.5" ide laptop hd, if you do , you can buy an adapter at compusa from 2.5" to 3.5" ide hd cable, they sell it for 10 bucks...

by lyle.macbride

The strange connector that you see is actually an adapter that slides on to the 2.5" hdd pins to allow then to 'click' into place on the laptop. Carefully slide it straight off and you will see the standard pins of a PATA 2.5" hdd.

You will need an adapter or an enclosure to get the data off of the laptop hdd. I use a USB2 device that I purchased at a local computer store for about 30$. You can see it at:

http://www.slashgear.com/apricom-drivewire-makes-cloning-your-hard-drive-easy-319269.php

It also comes with the necessary software to make a backup image or a "clone" of the drive if that is what you want.

Once you get that or something similar all you need to do is to carefully attach it to the drive and plug it in to a usb2 slot on your PC or Mac. (Since it is USB there is no need to set as a master.)

Hope this helps, and good luck.

Cheers!

This discussion is closed to new replies.