Discussion Locked

SATA drives

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,

I have a question regarding SATA drives for which your help will be greatly appreciated.

I have two SATA drives installed on my computer and they are working fine within WINXP SP2.

I don't remember if the drivers were installed with WIN XP or if I have installed later on when installing the drives.

The problem is when I try to boot on a CD for various reasons, for exemple DRIVE Image CD or WIN XP CD they (the SATAs) are not recognized.

When I tried to boot on the CD(s) I took care to press F6 and insert the floppy containing the SIL3112r (received from the mother board supplier, ASUS)into the drive A; that driver is loaded but when the boot process is finished the SATAs are not recognized all the same.

Could anyone give me a hint?
The mother board is a P4S8X\LAN\1394\SATA\GOLD-UAY from ASUS.

Thank you for any input.

14 replies

by wcp

According to the manual, the SATA controller is Promise (PDC20376 or FasTrak376) not Silicon Image (SIL3112r).

You need to make an appropriate floppy (see section 5.5.4 on p93) and install the driver after F6.

by nhiep_nguyen

Poster rated this answer.
When I asked ASUS, they sent me the SIL3112r but the customer service could be lousy enought not to know.
If you know where I can get the ones you mentioned I'll try to get them; unless you could send them to me.
Thank you in advance.

by cg it

Windows sees SATA drives as Mass Storage Devices, e.g. SCSI. The Promise SATA controller is not ATA or the primary controller which inherently Windows tries to boot from [example: boot floppy, boot CD, boot HDD-0. The boot order needs to be changed to reflect boot SCSI.

Also, you need to create an array for the drives [striped or mirrored] using the Promise Fasttrack Controller software and make sure that array is bootable. Once the array is made, and the boot order changed to boot SCSI, load Windows pressing F6 to load the SATA drivers. After the initial setup files are copies Windows reboots and will boot to the SATA array.

by nhiep_nguyen

Poster rated this answer.
I know all that, the problem is the only SATA driver I have on a floppy doesn't see the drives when I boot up without WIN XP.
When I boot with XP, my SATA drives are working fine. There must be a driver within win XP, I ignore which one.

by neil cotton

If you are trying to install Windows XP, make sure you have the full SP2 install version, and 90% of the SATA drivers are on there, and automatically resolve the Mass Stoarage Device problem when you press to install 3rd party drivers on the hardware scan prior to installation.

by nhiep_nguyen

Poster rated this answer.
As I said when I am within Win XP, I have no problem with the SATA drives; the problem arises when I boot from a CD and press F6 and load a driver in order to see the SATA without XP.

by wcp

This is a continuation to Answer 1.

The driver is in the motherboard CD. You need to copy appropriate files to a floppy. I do not have the CD or manual with me. I went to the website (www.asus.com) to find the info (I downloaded the manual). Perhaps you can do that too. You can also download the drivers! Read very carefully the Section 5.5.4 on page 93.
If you do not feel comfortable of doing this, have a knowledgeable person do the job for you.

by nhiep_nguyen

Poster rated this answer.
In my mother board (P4SX8) ther is not that driver. I am confortable with various operations including updating the firmware but the problem is I do not have the appropriate driver.
On ASUS.COM they have drivers for recent mother board, mine is about 2 to 3 years all.

by jasonbis

Within Windows XP do you have the drives in a RAID configuration? One option that might work is to go into the BIOS and put your SATA drives into combination mode. I forget the different modes available but at least on Dell machines it is called combination mode. Dell sends us PC's all the time with SATA drives that are set to RAID mode. They boot just fine into Windows but if we boot off a Ghost CD or something it doesn't recognize the drive. Since there is usually only one drive in there anyway we change the BIOS setting from RAID to Combo and Ghost can now see it. Asus BIOS may use different wording but see what your options are in there and try it again.

by nhiep_nguyen

Poster rated this answer.
My SATAs are in Combno (striped) mode. Even in combo (striped) mode when I boot up with Drive Image Rescue CD they are not recognized.
When my computer crash (the OS is installed in an ATA drive) I got to have the image on another ATA not on SATA.
I also have a second boot on SATA but I got to do a trick: I install the OS on an ATA then withi windows I make an image of the boot drive and restore it on the SATA since within windows they are perceived.
But this is not very convenient nor elegant.

by nhiep_nguyen

My motherboard has two connectors for ATA one connector for Promise Fast Track and also two connectors for SATA drive (narrower connecting cables). The Promise Fast Track drives are seen alright within or without WIN XP.
It is the SATAs that are concerned in my question.

by nhiep_nguyen

WCP is right, the SATA drives are seen as Promis Fastrack on the ASUS motherboard.
I've realized when I reinstalled windows and the sata drives were not seen until I used the motherboard CD to install the Promise drivers.
The problem is the drivers are imbeded in the motherboard CD and I do not know how to copy the appropriate files to a floppy so that to be used when booting from a third party CD.
Could anyone tell me How?
Thank you

This discussion is closed to new replies.