Question Locked

Server room cabling help neede

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello everyone,

As you know how difficult to maintain a server room cabling.
I need someone's help in organising my servere room cabling especially for server power cable, ethernet cable and display, mouse and keyboard cableing.

Other part cavling is looks good i did it.

We have five servers mounted in rack.It is a simple rack so we used screw to mount the server in rack.

now real night mare is we are using APC ups which supplies power to all server. so from APC ups power goes to extension board( we have four of them)and from extension board power goes to all server. but if you look at the picture it looks like very meshed up because all cables are lying on floor and so twisted to find cable is really difficult.

can any one suggest me how do i plug the power cable from ups to all server so it looks decent and nothing is meshed up.
I tried to find out documentation on this but i am not successful.

all your help is highly wel comed.

Wel i nadvance thanks for yout help and time.

Thanks,
Bharat

9 replies

by oh smeg

So all you need is a lead from the UPS to the Rack and then everything is powered directly from the Rack. This involves making up your own Power Leads and installing Electrical Outlets in the actual Rack and also Custom making your Power Leads so that they are only long enough to run from the Power Socket to the Server. Just remember that you need to maintain Electrical Safety so this should be installed by a Qualified Electrician particularly if you have a Metal Server Rack as this will require Earthing to prevent any possibility of Electric Shock and or Death.

As for the Network cabling you need to keep this away from the Electrical Cabling or you could loose the Networking Connections from Low Frequency Electromagnetic Interference. The standard here is to maintain at least 4 inches of separation [i]mininum more is better though[/i] between Mains Leads and Network Cabling at all times. Again you need to custom make the leads to the length that is required and make them as short as possible.

I'm not sure about Monitor Keyboard or Mouse leads as I tend to have servers that run headless so I don't have any of this stuff actually attached but I suppose you could just run 1 set of Keyboard/Mouse/Video and then switch between the different Servers with a KMV switch. These can be either a small unit or a standard Rack Unit that bolts directly into the Rack and is accessed from the front. It depends on the Sever Rack here.

Is that of any help?

Col

by bharat_p80

Hi Smeg,

Thanks for your wonderful thoughts. It's really helpful to me i am sure.
I just wanted to tell you that i am usi ng the KVM switch and running just one cable for mouse, keyboard and video from this switch to Display, keyboara nad mouse .but we have 5 servers in rack so there are five such three cables pair coming from each server to KVM switch and all these cables are lying on floor because they are too big.

We are using an open Rack in which we mounted servers with just two bolt.
I do not see any idea how can i run power cable because there are
5 server------two cable for each server---10 cables
2 firewall----2 power cables
2 routers-----2 power cales
4 switches----5 power cable
1 cisco router---1 power cable
1 cable modem----2 power cable
1-dsl router---1 power cable
-----------------------------
total of 23 power cable i need to run through RAck.
how can i get rack mounted power strip?
do i get such big strip which can hold 22 power cable?

if you have any such product info please send me.
also if you can provide me server room wiring pictures specially for power cables wiring i would be really happy person.

Other than that i understand what you have said.Once again thanks for your valuable time and suggestion.

thanks,
Bharat

by oh smeg

Depending on whatever Electrical Safety Laws that you have to comply with over here you can have 25 Outlets on the 1 Circuit. So you could screw mounting Blocks onto the Back of the Rack and mount multi switch Power Points on them and run the necessary wiring at the back of the rack out of sight. That way there would only be 1 Power Lead visible if there isn't a Power Outlet behind the Rack.

As for the KMV Switches I use a Rack Mount One that plugs in the back of the Switch and only has the controls on the front basically push button whatever to switch to the Server/whatever. Not much you can do about the Video, Keyboard, Mouse Leads though as they are a necessary evil and the Wireless Keyboard/Mouse option isn't suitable for a Server application as there is too much likelihood of having your Server Hijacked by someone else running the same hardware close by. Though it's funny to watch end users when the same thing happens go crazy insisting that they have lost control of the Mouse & Keyboard. :D

Perhaps something like this would work for you

http://tinyurl.com/2nzxp9

Though that is only a suggestion and I'm not recommending that store I just found that on a Goggle Search for 8 Port KMV Switches. You obviously don't need one of the 24 Port ones that I use.

I tie all the Leads that are not Power together and tie them to the Rack with Cable Ties.

The Power Leads are the first to install and use Plastic Cable Ties to hold them in place. The Cable Ties are just a plastic thing that you loop through the end and pull tight. You do need to cut off any excess length off the bit that you have pulled through but this is a simple process.

Col

by bharat_p80

Hi Smeg,

Thanks once again for your quicker response.I admire all your helps.

I am going to attach some pictures i took for server room......
Here is the link you can watch them.......

http://www.putfile.com/pic.php?img=7320275

There few pictures you need to take a look at all picture and let me know where and how i can put server power cable so i can remove jungle of cables from the back of RACK.

I have KVM switch attached to Rack.
I need Rack mounted power strip so that i can connect all servers power cable to the Rack mounted poer strip.
Just take a look and let me know your suggestion for making server room cabling nice,clean and pleasant looking.

Thanks,
Bharat

by oh smeg

Yep there a few wires involved there aren't they? The main problem is that you have an open rack which I hope is bolted to the Floor I couldn't see in the Pictures. All of the ones that I use are enclosed cabinets where you can hide the worst of the Mess of Wiring out of sight, but in a case like this you are stuffed completely as there is no place to hide anything.

About all you can do in a situation like this is make the best of a bad situation and tie as much as possible together so it looks less messy but it's not going to improve the situation much as even if you manage to get rid of the Power Lines the Networking Cabling is going to remain messy no matter what you do.

About all I can suggest here is to tie as much as possible together like the Buildings LAN Cables & Phone Cables where they emerge from the Ducting to the building and then run to the Patch Panel and the remaining phone lines which look about the diameter of a mans arm tied together and attached to the wall as neatly as possible. However you will still have a messy pile of wires where the LAN Cabled emerge from the Patch Panel and the Switches not much you can do about that here though as you can not hide the cabling in any form.

Even the Mains Leads will be very hard to make look presentable in a situation like this as there is nowhere that you can hide them from sight.

About all that is possible here is to run a Power Take Off on your Actual Rack and custom make the Power Leads to as short as possible so that there is not much hanging down but that will only be a marginal improvement to looks and make no improvement to function unless you count the possibility of leads not being accidentally pulled out because someone trips over them. Ideally all of this should be inside a cupboard/enclosure where is remains invisible just provided that there is enough cool air being pumped in the Serves will remain cold enough. Ideally an opening at the bottom that allows cold air to be sucked in and several Fans at the Top extracting the heated air out of the enclosure.

With a setup like this I'm not sure what else can be done.

Col

by tig2

Possibly some wire management clips so that you have wire running in some logical and neater formation. But truthfully, yor rack looks to be at capacity now so it is hard to see where you can add this in.

I agree with Smeg- an enclosure is a much more stable and secure environment and considering the value of what you are protecting, extremely good value for the money spent.

Good Luck... and don't forget to mark Smeg "Helpful"!

by bharat_p80

Hi Smeg,

I must be thankful to you for all your help and suggestion.
Now i will try to minimize this jungle and will send you and updated picture of the same server room once i am done.

Thanks,
Bharat

by oh smeg

You're going to need it.

Thanks I would like to see what you come up with.

Col

This discussion is closed to new replies.