Ah thanks, however I'm a bit smarter than that. Though you get dumb when you sit to much with cisco.
I had an working conifiguration several times over and I never understand why it didn't work for me when it did for others.
So I installed Win2003 server on a laptop and everthing went fine. It was very easy to configure the dhcp server and as well like the ip helper command. The only problem was that I belived everything were fine since one vlan/scope always worked without any problem.
Yes there's a lot of trunks ports, pinging within Vlans always worked. Pinging over vlans worked this time when I reconfigured everything, don't rely know what went wrong.
The topology I had were big so I had things pre-configured, each switch had two trunks. The access ports were however randomly created here and there untill things got working.
I have been sitting with this for a very long time, and the problem ended up being that I ran it in vmware, never been good with vmware either.
Here's the working configs(everything not listed as shutdown.
Core#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6
Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
5 Server/Management active Fa0/12
10 Accounting active
20 Marketing active
30 Engineering active
hostname Core
no aaa new-model
ip subnet-zero
ip routing
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/3
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/5
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/6
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/12
switchport access vlan 5
switchport mode access
description DHCP_AD_DNS_Server
interface Vlan1
no ip address
shutdown
interface Vlan5
ip address 192.168.1.2 255.255.255.0
interface Vlan10
ip address 192.168.0.1 255.255.255.0
ip helper-address 192.168.1.1
interface Vlan20
ip address 192.168.2.1 255.255.255.0
ip helper-address 192.168.1.1
interface Vlan30
ip address 192.168.3.1 255.255.255.0
ip helper-address 192.168.1.1
router ospf 1
log-adjacency-changes
network 192.168.0.0 0.0.0.255 area 0
network 192.168.1.0 0.0.0.255 area 0
network 192.168.2.0 0.0.0.255 area 0
network 192.168.3.0 0.0.0.255 area 0
ip classless
ip http server
line con 0
password Password123 <-Win2k3 demanded a strong pass so used it everywhere.:P
login
line vty 5 15
password Password123
login
One of the Office Switches:
hostname Office_B01L01
interface FastEthernet0/1
switchport mode trunk
interface FastEthernet0/2
switchport mode trunk
interface FastEthernet0/3
switchport access vlan 10
switchport mode trunk
interface FastEthernet0/4
switchport access vlan 10
switchport mode trunk
interface FastEthernet0/5
switchport access vlan 10
switchport mode access
<---blabla-->
interface FastEthernet0/24
switchport access vlan 30
interface Vlan1
no ip address
no ip route-cache
interface Vlan5
ip address 192.168.1.6 255.255.255.0
no ip route-cache
interface Vlan10
no ip address
no ip route-cache
interface Vlan20
no ip address
no ip route-cache
interface Vlan30
no ip address
no ip route-cache
line con 0
password Password123
login
line vty 0 4
password Password123
login
line vty 5 15
password Password123
login
I ended up not needing to install the DHCP relay Agent in Win2k3 though. Worked fine without it.
Thanks for all the Help though, atleast I got to try something else rather than getting stuck on the same problem all the time. To much Cisco makes you dumb.:P