Discussion Locked

strange network traffic UDP port 21945

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have networks in 2 locations WAN'd by T1. Today I was looking at the firewall logs and the syslog and noticed quite a bit of traffic on the 10 node network and one pc on the 70 node using UDP port 21945. I didn't have a whole lot of time today to look at it but a quick netstat showed port 21945 in a wait state. These PCs were sending to 10.0.0.255 so nothing was going ooutside. Any ideas??

Thanks!!

14 replies

by roots

the best way to control your network is to use a cisco router , you will be able to monitor all your network connections & bandwidth used by each user what ports & what ip address they are connected to.
you can block all ports that you think it is eating you bandwidth but creating access-lists.
how to do that ? ok :
for example to block kazaa uploads do the following:
access-list 120 deny tcp any any eq 1214
access-list 120 deny udp any any eq 1214
access-list 120 permit udp any any
access-list 120 permit tcp any any
----------------------------------
then go to int e0 & add the following :
ip access-group 120 in
ip access-group 120 out
----------------------------------
that will solve your problem hopfully

by joeblough

Yes that would help... for a few thousand bucks hehe! I can block it now... I want to know what it is and why its on every PC in my remote office and one here. Blocking is the easy part... I prefer to find out what things are before blindly blocking ports.

by joeblough

Here is a sample packet...
- - - - - - - - - - - - - - - - - - - - Frame 4 - - - - - - - - - - - - - - - - - - - -
DLC: ----- DLC Header -----
DLC:
DLC: Frame 4 arrived at 10:43:53.5528; frame size is 60 (003C hex) bytes.
DLC: Destination = BROADCAST FFFFFFFFFFFF, Broadcast
DLC: Source = Station CmpPrd0F2B00
DLC: Ethertype = 0800 (IP)
DLC:
IP: ----- IP Header -----
IP:
IP: Version = 4, header length = 20 bytes
IP: Type of service = 00
IP: 000. .... = routine
IP: ...0 .... = normal delay
IP: .... 0... = normal throughput
IP: .... .0.. = normal reliability
IP: .... ..0. = ECT bit - transport protocol will ignore the CE bit
IP: .... ...0 = CE bit - no congestion
IP: Total length = 31 bytes
IP: Identification = 26528
IP: Flags = 0X
IP: .0.. .... = may fragment
IP: ..0. .... = last fragment
IP: Fragment offset = 0 bytes
IP: Time to live = 128 seconds/hops
IP: Protocol = 17 (UDP)
IP: Header checksum = BE05 (correct)
IP: Source address = [10.0.0.42]
IP: Destination address = [10.0.0.255]
IP: No options
IP:
UDP: ----- UDP Header -----
UDP:
UDP: Source port = 21945
UDP: Destination port = 21945
UDP: Length = 11
UDP: Checksum = B602 (correct)
UDP: [3 byte(s) of data]
UDP:

by Former member

Hmm...a network UDP broadcast to port 21945, from the same port. Must be some kind of Application, or perhaps a service, that uses high ports. Does not seem malicious however, since it is only limiting to your network, not the world. At least as far as THIS packet capture goes. Who knows what else these workstations are sending? Now you need a program that tells you what program is using that port. Any ideas on a freebie?

I would start by reviewing every app and service installed on the machines. This is definately not a well known app, so that pretty much defines what to look for....Good luck, maybe you can post the results of your findings.

by Former member

This is very suspicious and it's good that you are looking into it. I mean, most, if not all, legitimate apps do not use the high ports..This is why they are blocked at most firewalls...

by Former member

Yes, from the poster below, that Active Ports is defeinately working for me, and should help you as well. Please let me know, you can also email. thanks.

by joeblough

Active Ports did the trick. It's e-token, a licensing module built into some surgical planning software. Turns out is's ok, but I need to talk to the programmers, this broadcasts from every PC with the software loaded every few seconds. Won't be long before some hospital IT Mgr is calling me to see what our laptops are doing!! At least now I know, and maybe can get it slowed down to every 5 minutes instead of every 5 seconds! Thanks -Q

by joeblough

OK.. now we're on to something... anyone know of an application that will tell me what apps are running on which ports??

by curacao_dejavu

There is a free program called active ports which you can find at download.com. You have to run this on the oc that is behaving strangely.
If you didn't do already, run a antivirus on the pc to check for viri and trojan horses.

a search on google "port 21945" shows that is is some cgi script code, with permission denied.
check if IIS is running on that pc.

Leopold

This discussion is closed to new replies.