Discussion Locked

Stupid Old PC and the new HD

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Ok here we go, I'm on a super old compter and I've been trying to add a new hard drive but everytime I try something different I get lost again. I origanally tried to partition and reformat the hd but when I tried to setup windows the computer wouldnt read the cd rom drive and I later found out that since the cd rom was connected to the sound card I had to setup the sound card first but even after doing that nothing happend ( grrr ). So then I decided to just try to let windows control the new hd as a slave, so I set the jumpers and hooked it up then started up the computer and it appears all seems good but then as soon as I tried to put anything on the new hd ( which has been partitioned and reformatted again ) I get a write error on a blue screen then I look in the computers properties to find out that theres a ms-dos compadability issue between my C: and D: drive. Im out of ideas please help.

Thanks for your time,
Chad

12 replies

by shakeelr7

My friend, you forgot to tell that at what age your computer stands. Is it in the age of Pentium One or Two or 486XX or 386XX neither you mentioned that on that system how much capactiy of HDD you are using. Well, If your system is able to detect your HDD then it can run on it.
the MS-DOS cpmpatability issue arrise when you have formated or fix the disk with the old OS and try to run WIN32 Application or TRY to run WIN32 System Utilies. But it does not bother you too much.

The blue screen comes with a lot of othe issues. It may be your processor bad or your memory bad or some card like sound, fax, VGA.

Most of the time blue screen comes when your memory goes bad and if you are using IBM or Cyrix made processor then because the Heatup too much so because of their overheating the blue screen comes.

i answered more than your question, considering that may be from all of them you will be able to find your answer.

by shakeelr7

My friend, you forgot to tell that at what age your computer stands. Is it in the age of Pentium One or Two or 486XX or 386XX neither you mentioned that on that system how much capactiy of HDD you are using. Well, If your system is able to detect your HDD then it can run on it.
the MS-DOS cpmpatability issue arrise when you have formated or fix the disk with the old OS and try to run WIN32 Application or TRY to run WIN32 System Utilies. But it does not bother you too much.

The blue screen comes with a lot of othe issues. It may be your processor bad or your memory bad or some card like sound, fax, VGA.

Most of the time blue screen comes when your memory goes bad and if you are using IBM or Cyrix made processor then because the Heatup too much so because of their overheating the blue screen comes.

i answered more than your question, considering that may be from all of them you will be able to find your answer.

by csmith

DOS compatability mode is an OS problem.
Which OS are you running?
That the PC could not address the CDROM indicates that you probably plugged the new HD into the CDROM cable. (It can also be a settings problem, see last note.)
Never do that. TheCDROM will "slow down" the new hard drive, because under old BIOS's all the devices on an IDE channel run at the same speed.
Old CDROMs are very slow.
Plug the new hard drive into the same cable as the C: drive, and try again.
Yes, you do want the new hard drive to be D: (The slave drive on the primary IDE.), and the CDROM should be E:
Make sure that the CDROM is not set or locked as D: in the software. If it is, change it to E:
Check your config.sys and autoexec.bat files first for this.Regards, Chris

by cluseau1

Try changing your settings in fdisk. This will make your hd report a smaller size. You did say a NEW hd didn't you? If this doesn't work your bios will simply not support this new hd. You didn't say how old your pc is. Sometimes the bios will appear to accept your hd but in reality it still wont work and nothing will help. try tricking the bios in fdisk. Let me know if this works. It has worked for me in the past if your pic isn't too old.

by cluseau1

Format your hd as a master. Then set your jumpers to salve and chain it off the C drive. do not attempt to install an os on this new drive. on boot up it will report win already running. Either that or switch drive assignments and format your old drive and use it for storage as the slave. again if your system is a pentium grade I or lower forget using a large hd such as a 20 or 40 gig hd. Attempting to use a hd such as a 40 gig could damage the board or processor. I suggest using a secondary IDE card. This may fix your problem. Not sure if a card will work with a 486 but will work with a pentium system. Good luck

by zlitocook

One other thing new large hard drives can not be seen or if they are they show up as a smaller size. All hard drive makers have drive managers you can down load. They let you use large hard drives in almost any computer. You need to connect the cdrom and the hard drive to diffrent ide connections on the main board, use the bios to detect the drives and use drive manager to install the hard drive. Then copy the win95, win98 ect folder from the cd to the new hard drive. When it can not find the cdrom to copy from point it to the folder on the hard drive.

This discussion is closed to new replies.