Question Locked

System can reboot but can't boot after shutdown

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have just replaced a power supply (400W) after confirming the old one (450W) was faulty. After replacement, the system is able to run normally with many rounds of reboot but it just refuse to boot after shutdown gracefully. The symptom is there is no beep sound and no video signal although the power LED shows running at the casing. I can see the fans are spinning. Strange thing is the system is able to boot again on the next day or after some hours. The same problem comes back again after shutdown gracefully. May I know could this be due to insufficient power supply? What is the probable cause if there is no beep and w/o any video signal? Many thanks in advance.

18 replies

by older mycroft

That would be my first concern.

Perhaps the 450W was under strain anyway, so replacing upward (500 - 550W) might have been a better idea.

Without knowing any details of your system and its hardware components, I really couldn't do any more than guess. ;)

by brel

Basically it's just a simple P4 machine with one SATA disk, CD ROM & AGP card. Wonder what's the minimum acceptable power supply for a P4? As it can function properly (after some rest) except after shutdown, i hope there is a way to confirm the faulty part before buying one. Thanks.

by rob miners

and you really should have gone for the same wattage or above. Ageing motherboards tend to suffer the most, with either the onboard NIC or the AGP slot or it effecting the memory modules.
Check the memory.
You can test the memory by running Windows Memory Diagnostic that can be downloaded from:

http://oca.microsoft.com/en/windiag.asp.

If memory problems are found, try re-seating the RAM. If it doesn't work, replace the defective RAM.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by brel

I'll try to run the memory test. Anyway I've tried clearing the CMOS but that doesn't help. Will update the result once I've test the memory. Thank you.

by brel

I could not run the memory test tool as there is no floppy drive in my system. I tried to test with one RAM at a time and the same problem still persist. So I doubt it's the RAM issue. Thanks.

by rob miners

isn't up to specs. To test this theory shutdown the PC and turn the power off from the outlet that is connected to the PSU and remove the cable from the PC. Plug it back in and turn on the power and see if you can restart the PC.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by brel

Just tried it out and noticed this behaviour: I have to power off the wall socket after the proper shutdown in order to boot successfully. Without switching off the wall socket (after the graceful shutdown), the system will fail to boot. Any idea what cause this? Many thanks.

by rob miners

that doesn't appear to be switching the power off to the board. Replace it with a swap and make up the difference if you can.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by brel

Probably that makes some sense.... Many thanks for your advice, Jacky!

by older mycroft

I knew it was a mistake to email you THAT link!

Now that you're referring to me as "HalfCut" you've gone and confused the OP! ;)

by rob miners

I get for trying to be a smart@ss. You are right the OP probably didn't realise what I was refering to. ;D

by brel

Sorry I was away from the net for the past days and miss all the actions. Anyway i must thanks Old Mycroft (hope i got your user id correct :-)) and Jacky for their expert advices in this thread. Many thanks and have a good day !!!

by rob miners

Yes I was referring to Old Mycroft as HalfCut. ;)

This discussion is closed to new replies.