Question Locked

SYSTEM CRASH/BLUE SCREEN WITH VISTA AFTER ADDING KEYSPAN USB PRINTER

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

SYSTEM CRASH/BLUE SCREEN WITH VISTA AFTER ADDING KEYSPAN USB PRINTER / NETWORK
SPOOLER Model: US-4A and connecting to MultiFunction KODAK 5300. I HAVE FOLLOWED
THE INSTALL INSTSTRUCTIONS. ADDED THE PORT TO FIREWALL. WHEN I CONNECT USING THE PROGRAM THE VISTA DISCOVERY PROCESS BEGINS FOR THE PRINTER. THE SCREEN GOES
BLUE AND RESTARTS IN RECOVERY MODE.Name: KeyspanUSBserver
Model: US-4A
Serial No: 13fd6
Firmware: 07-05-01 14:51 2.5 #417010
Connect Mode: Multi-User
IP Address: 192.168.1.103
UDP: 3842
TCP: 3842
Discovery: Multicast & Broadcast
Password Required: Yes
No. of Devices: 1
No. of Devices In Use: 0
Local Server Settings: Yes
Exclusive Access: No
Connected Clients 1
Name: [MultiFunction 5300]
USB Desc: [Eastman Kodak Company KODAK 530]
VID/PID: 040a/4026
Serial #: B78B0588
Share Mode: Shared
Password Required: NO
Local Password Saved: NO
Type: Printer
Auto-Connect Enabled: NO

13 replies

by mrtbenigno

Newest dirvers from keyspan and kodak... works with pc directly... printing/scaning etc... is it possible the driver/device it is searching for is Vista or kodak/vista? How can I determine what driver is crashing my computer? 2.5.119 Kodak driver 2.01 Keyspan/Vista compatible

by cg it

you might want to try running the Kodak program using XP SP2 compatibility mode if you know the program works with XP SP2.

right click the .exe file and choose compatibility mode, choose XP SP2

then try running the program

by mrtbenigno

I think it(Vista) is searching for the usb printer under "discovery/new device found" and when it loads the printer driver"found" I get the blue screen. Is it the vista(opperating system driver) or the Kodak/vista driver from Kodak that is causing the problem????

by cg it

they have both drivers and software plus firmware downloads. might check your firmware version and see if yours is up to date.

Question, when installing both software and the printer itself, does Vista's UAC prompt come up?

Look in device manager for your printer, what status does it show? you might want to download drivers to a folder, update drivers via the device manager and point it to the driver folder, see if that will work.

as far as software, If your using software that is not designed for the printer e.g. your trying to use software that is not from the software download page for the 5300 all in one printer, that might be your problem.

by mrtbenigno

when I installed the printer I used the cd with the 5300 that looks directly to the web site to verify the version and downloads it if it applies. there is no uac that comes up in the install. I was woundering how to change the port to the keyspan on the kodak driver... the problem may be with the driver supplied with vista and not from kodak web site!

by mrtbenigno

downloaded firmware and updated 5300. I also re-downloaded the software & vista drivers.

by cg it

probably is the problem.

have you tried installing the printer and Kodak software without the keyspan device?

From the web site : everythingusb.com these are the pros and cons: Note USB 1.1 support only...

Pros: Share USB devices on network; compact; easy to connect and configure.
Cons: Not all USB devices are supported yet; strictly USB 1.1 support.
Verdict: The Keyspan USB Server adds much needed flexibility to the USB front; it is easy to set up and works as billed.

I would see if the keyspan server is listed under the USB devices in device manager [disconnect the hardware].

installing the keyspan device should activate Vista UAC.

by mrtbenigno

I can view the device(5300) in the keyspan program....Name: [MultiFunction 5300]
USB Desc: [Eastman Kodak Company KODAK 530]
VID/PID: 040a/4026
Serial #: B78B0588
Share Mode: Shared
Password Required: NO
Local Password Saved: NO
Type: Printer
Auto-Connect Enabled: NO
The problem happens when I "connect"(buton)in the keyspan program is activated.... Vista activates discovery/device mode....UAC and that is when I get the blue/screen.. It seems to begin the process and then goes bad!

by cg it

under USB devices and see if the keyscan server is there...

by mrtbenigno

Keyspan USB Servers

NHCI Client Support

NHCI Client Support

Device type: Keyspan USB Servers

Manufacturer: Keyspan

Location: Unknown

Device status

This device is working properly.

by sbuxwest2

have you found a solution as i have the same problem my computer has vista and my printer is a kodak all in one 5500 and the screen goes blue and crashes when i try to connect to printer

This discussion is closed to new replies.