Question Locked

system error Event id 1003, 59, 32

0 helpful
2 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
i recently reinstalled windows xpsp2 on my system, some problem are facing. in my HDD 4 partitions made, when i going to open other partitions immediately PC gets restart. so i checked in Event viewer, i got some errors like event id's 1003, 59, 32 etc.
so please help me what i do for this problem.

Thanks and Regards
Sandip Bhosale.

2 replies

by rob miners

Click Start, right mouse click Computer and select Properties. Select Advanced System Properties, continue. Select Settings for Startup and Recovery. Untick Automatically Restart.

Minidump Files can be found here. C:\WINDOWS\Minidump\Mini******-**.dmp

How to read the small memory dump files that Windows creates for debugging

http://support.microsoft.com/kb/315263

To download and install the Windows debugging tools, visit the following Microsoft Web site:

http://www.microsoft.com/whdc/devtools/debugging/default.mspx

Instructions on using Windbg.

Open Windbg and select file, Symbol file path and brows to the Symbol folder that you have downloaded and installed Symbols to, select OK.

Close the workpage and save the Workspace information. This should lock in the Symbol path.

Open Windbg and select file and select Open Crash Dump then navigate to the minidump, highlight it and select Open.

There are two ways to use !analyze -v the easiest is to click on !analyze -v under Bugcheck Analysis.

When you have ran the initial dump if you look to the bottom of the screen you will see kd> to the right of that type in !analyze -v and press the Enter key.

Ctrl + a will let you copy the information and paste it into notepad.

Look to the bottom of the page for information like this. This was fixed by updating the Graphics Drivers.

FAULTING_THREAD: 864f6a98

DEFAULT_BUCKET_ID: GRAPHICS_DRIVER_FAULT

CUSTOMER_CRASH_COUNT: 1

BUGCHECK_STR: 0xEA

PROCESS_NAME: logon.scr

LAST_CONTROL_TRANSFER: from 00000000 to bfef0fea

STACK_TEXT: f6434e6c 00000000 00000000 00000000 00000000 sgiul50!DrvBitBlt+0x585

STACK_COMMAND: .thread 0xffffffff864f6a98 ; kb

FOLLOWUP_IP: sgiul50!DrvBitBlt+585 bfef0fea 75f9 jne sgiul50!DrvBitBlt+0x580 (bfef0fe5)

SYMBOL_STACK_INDEX: 0

SYMBOL_NAME: sgiul50!DrvBitBlt+585

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: sgiul50

IMAGE_NAME: sgiul50.dll

DEBUG_FLR_IMAGE_TIMESTAMP: 3b7dfec7

FAILURE_BUCKET_ID: 0xEA_IMAGE_sgiul50.dll_DATE_2001_08_18

BUCKET_ID: 0xEA_IMAGE_sgiul50.dll_DATE_2001_08_18

You can try running chkdsk X:/r on all the drives from a command prompt. X is the drive letter that will have to be substituted.

You can use the Hard Drive Makers Testing Utility to Test the Drive

Hitachi / IBM - DFT "Drive Fitness Test"

http://www.hgst.com/hdd/support/download.htm

Works with all manufacturers

Western Digital "Data Lifeguard"

http://support.wdc.com/download/index.asp#dlgtools

Works with WD drives only

Fujitsu "FJDT"

http://www.fel.fujitsu.com/home/drivers.asp?L=en&CID=1

Works with fujitsu models only

Samsung "hutil"

http://www.samsung.com/Products/Hard...ties/hutil.htm

Compatability unknown...

Seagate "Seatools"

http://www.seagate.com/support/seatools

Works with Seagate drives only

You can test the memory by running Windows Memory Diagnostic that can be downloaded from http://oca.microsoft.com/en/windiag.asp. If problems are found check the steps below.

Also check Capacitors around the CPU for swelling or bulging.

As the capacitor ages, its capacitance decreases while its equivalent series resistance (ESR) increases. When this happens, the capacitors no longer adequately serve their purpose of filtering the direct current voltages on the motherboard, and system instability results. Some common symptoms are:

* Not turning on all the time; having to hit reset or try turning the computer on again
* Instabilities (hangs, BSODs, kernel panics, etc.), especially when symptoms get progressively more frequent over time
* Vcore or other system voltages fluctuating or going out of range, possibly with an increase in CPU temperature as the core voltage rises
* Memory errors, especially ones that get more frequent with time
* Spontaneous reboots
* In case of onboard video cards, unstable image in some video modes
* Failing to complete the POST, or rebooting before it is completed
* Never starting the POST; fans spin but the system appears dead

Test the Power Supply Unit and the CPU.

Download Prime95.

http://www.mersenne.org/freesoft.htm

Prime95 is used to put your system at full load. Prime95 - When run for the first time, it is necessary to click on Advanced, then click on Round off checking so that errors caused by instabilities will be flagged as they occur. Also go to Options and run the Torture Test. Run the Inplace FFTs (Max Power, Heat and some Ram). Prime95 will automatically thread all Cores, and will expose insufficient CPU cooling and computer case cooling, or excessive Vcore and overclock. At no other time will a CPU be as heavily loaded, or display higher temperatures, even when OC'd during worst-case loads such as gaming or video editing. Prime95 can be used with SpeedFan to observe CPU temps, while stress testing for system stability. During single threaded gaming and applications, Core 0 typically carries heavier loads and higher temps than other Cores.

You want your system at full load when checking your voltages to ensure your PSU is up to spec.

If your PC restarts during this test you have a faulty Power Supply (PSU) and it will need replacing.

Download SpeedFan and check the Voltages and Temps while Prime95 is running.

http://www.almico.com/sfdownload.php

You will want your 12-volt rail to be within 11.52 to 12.48 during load. This means when you are running your cpu at 100% you do not want to drop below 11.52 or you may experience stability problems including but not limited to system restarts and Windows crashes. For the 5-volt rail, you want it to be within 4.8 to 5.2 to be within the 4% range. As for the 3.3 volt rail, you want it to be within 3.17 to 3.43

Keep us informed as to your progress if you require further assistance. ;) :D

This discussion is closed to new replies.