Discussion Locked

T2682 eMachine Trouble - Power Suppy? Motherboard? CPU? RAM?

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

A friend of mine was having trouble with their computer and asked for help...

Two weeks later, I'm still working on it. I would appreciate any advice from the experts out there!

Original symptom: Press power button, nothing at all happens. No signs of life.

Let me give a brief troubleshooting rundown:
1. I originally suspected the power supply. Therefore, I brought home a few replacements for testing. None had any affect on the problem.

2. To isolate the power supply problem, I bought a power supply tester. It indicated that the PG was off the map and the +5V reading was inconsistent. Ah ha!

3. The power supply was replaced with a quality unit that tested well with my new tester.

4. My next assumption was that the bad power supply took the MB (Imperial GV 20030812) with it. In order to avoid trouble with the Windows XP OEM version, I opted for an exact replacement vs. an completely new (and better) MB. I found a match on eBay (used) and installed it today with the new PS. I took pictures of the original config to ensure that I got it correct upon installation. The net result of the new MB was a change in behavior, but all was not well.

New behavior: HD light stays on orange after pressing the power button. No CPU fan. No beeps. No video.

5. This new behavior seems to rule out the power switch. Does anyone agree with this assumption?

Where should I turn next? Should I assume that the bad power supply took out the CPU on its way out? RAM? CPU Fan? Would any of these cause this type of behavior?

How can I be certain that the new MB is working properly?

I would appreciate any assistance here. I am a computer professional, but I am certainly no expert in this arena.

Thanks!

David Stickney

9 replies

by mjd420nova

You're still not getting full power everywhere you need it. Isolate the power supply to just the MOBO, no drives or plugin cards. The 5 volts is just the logic and the 12 volts for fans, drives and option cards. Some video cards require another 12 volt connector. When you installed the new MOBO did you notice any insulating washers on the standoffs or glued to the bottom of the old MOBO?? These can be overlooked. If you can get it to power up properly, then add the video card, and then the drives, one by one. Once you get the thing going again, boot to the WINCD and do a repair of the OS, not a restore.

by dp_stickney

OK. I followed your steps and did find something of interest. The drive light went out when only the DVD drive was plugged.

Configuration of drives from top to bottom:
1. DVD
2. CD
3. Floppy
4. HD

With only #1 plugged, the drive light goes out. Not sure what this means.

Other items of interest:

1. I did notice that the CPU fan twitches when I hit the toggle on the back of the power supply.

2. The power supply fan comes on when I press the system power on button on the front.

3. I swapped out the memory with no change in behavior.

4. I re-tested the power supply. It reads:
+5v = 5.0
+12V1 = 12.5
+3.3V = 3.3
-12V = 12.0
+12V2 = 12.5
5VSB = 5.2
PG = 330ms

Do you suspect that the power supply is behaving poorly under load or something? Given the current results, should I continue to pursue the power supply?

Thanks for the help!

Dave

by dp_stickney

I swapped power supplies with a known good system and found that the problem did not follow the power supply, it stayed with my troubled system.

Question: Can a fried CPU cause a problem like this?

Running out of ideas...

David

by absolutely

Optical drives (ones that aren't broken!) are not particularly high load devices; even crappy, off-brand/generic 350W PSUs handle a couple optical drives & a couple hard drives, at least until the most recent, high-drain processors and video adapters. You have a short somewhere in your DVD drive causing excessive current to be drained from your PSU. Try another DVD drive, or just leave that one unplugged until you get a new one.

by pc21geek

Emachines are famous for frying one of the chips. Look very closely to the motherboard. I have seen this on many Emachines before. Looks like a bad PSU, but really needs a motherboard. The one you bought off ebay might be fried as well. Good luck, and let us know what you find please.

Kevin

by dp_stickney

Thanks Kevin. I scanned the new motherboard for any scorch marks around the chips and found none. Let me know if you have any other ideas.

Dave

by dp_stickney

I finally located a "new" CPU that I could use to test the "new" MB. I inserted a 1.6Ghz P4 and to my surprise, the CPU fan began to spin and the system booted. I was shocked. Everything seems to be working great. No complaints by Windows XP whatsoever. At long last, I think I may be finished with this project!!

Moral of the story: If you own an emachine, do yourself a favor and replace the power supply with a quality unit. In this case, the faulty power supply took out the MB and the CPU.

Thanks!

David Stickney

by dp_stickney

Last night, I removed the MB to examine the posts and bottom side of the MB. All posts and MB were clear of any type of insulators. Therefore, the connections all appeared to be solid.

From my standpoint, the problem seems to be narrowed to either the CPU or the MB. Any other thoughts?

Out of ideas...

David

by absolutely

Your previous post seems to contain the answer. Not sure why you continued testing the power supply & other primary components after such strong indication that the DVD drive is *the* problem. (?)

This discussion is closed to new replies.