Question Locked

trouble installing new hard drive

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a old Systemax 550Mhz with 640MB ram that was running WinXP Pro, the hard drive died and I ordered a new "WD1600AA" it did not come with installation software but I down loaded that from WD.
The hard drive is recognized and I burned WD Data Life Guard for DOS to a CD (using both Roxio as specified by WD and drag & drop with Windows) I am following the printed instructions and the system won't read or boot from the disk,
so I down loaded the same program but for floppy and tried to save to the floppy (the floppy on my system which is much newer is a USB) I have tried many floppies and I keep getting error; to close the write protect on my disk. it is in the manfacture setting which I call open so data can be added. I use this floppy all the time and have never had a problem. Also, I have tried booting from the WinXP CD, I keep getting the message that it can't read from the CD and I've used 3 different CD's. I have changed the both CDroms twice to drives that I know are good, in setup I have changed boot order as needed. Never had this many problems with a drive before.
I have not tried to install an older version of Windows and then upgrade, but maybe that is the next solution. I have been through a dozen CD and countess floppies. Another option I haven't tried is to install another hard drive with OS loaded then use the Windows ver. of WD DLG running this new drive as a slave and setting it to be bootable, using that option it will copy data from the other drive which I don't really want since this Systemax isn't mine.
Needless to say I would greatly appreciate any help offered. I'm sure I've forgotten to mention something.
Much thanks, shetech52

12 replies

by oh smeg

As this will be an IDE Drive it relies on BIOS to recognize the Drive and every BIOS has a Upper Limit on the size that they can read. If the HDD exceeds the BIOS Limit it will not work with that M'Boards IDE Controller as the controller [b]Can Not[/b] tell the HDD where to write the data to as it is mapped incorrectly.

If that is the case here you need to fit a IDE Controller Card and boot off that from the Windows Install Disc and you'll need to copy the IDE Controller Cards Driver to the Root of a Floppy and add it's driver with the [b]F6 Option[/b] when the first blue Screen appears on the Windows Installer. Just like you would add a SATA or SCSI Driver.

If you want the Floppy to work you'll need to lock the Floppy to prevent data being written to it by your description. +This involves moving the slide on the Floppy to the Locked Position.

Col

by shetech52

Not sure I understand exactly what you are saying, this is a procedure that I know nothing about. I can research it but it would be helpful if you treat me like a dummy at this point. The old hard drive was 40GB the new one is 160GB, I live in a very rural area (3 hours to shopping) and I happen to have this drove on hand)not sure if it makes any difference but she won't need that much drive so can I partition it and just use maybe half of it, would that help at all? Also. I have a Hitachi Deskstar 60GB that was only used for a couple of months, I could wipe it to use if necessary. I will go out and research info you have given me so far. Sorry I don't intend to sound stupid, I just haven't run accross this problem before. Any further help ou can offer would be great. Thank you for the help thus far.

by rob miners

drive is probably too big for the PC. Try setting the 60GB drive up and see how you go. ;)

Keep us informed as to your progress if you require further assistance.
:)
< all that to get a smilley to work >

by 1bn0

You should be able to boot from the cdrom without any hard drive attached. If you can't get it boot from a cdrom you won't get very far.

Some older systems would not boot from a cdrom on the secondary ide conroller port. Have you tried putting the cdrom on the primary port and configured as slave?

As for the floppy, the write protect hole needs to be closed. "You can't write on a hole". Your USB drive may be ignoring the write protect switch.

It is also very unlikely that the system will address a hard drive over 137 gb.

See http://www.48bitlba.com/

Use the 60 GB once you get it to boot from CDROM.

by rob miners

I suspected that the CD wasn't working because of the new drive. :D

by shetech52

The CD drives work fine when the new drive is installed as a slave...... this is driving me crazy. Thank you I really appreciate you help.

by shetech52

Must have not stated that well, I can boot from the CD, just can't boot the WD DLG for DOS to format the new drive.
When I put the new drive in as a slave and run the WD Data Life Guard for Win it recognises the drive and offer to set it up as a 137GB drive and will make it bootable, which is all fine.... but it automatically copies the files from the master drive which is and extra drive of mine and I don't particularly want that data transferred, nor do I really want to have to remove it all later. The problem is with installing the new drive by itself, the WD DLG for DOS won't boot (and I have recreated that disk 3 or 4 times) also if I boot directly to the Win XP disk it goes through setup, the MS aggreement which is F8 to agree and then says it can't read the CD and I have used 3 different original version plus a copy. It reads the both the Liteon CDRWand the DVDrom in Windows but can't seem to read them in DOS or Windows setup. Also, I have the CD's alternately set (with jumpers and in setup) as Secondary Master. When setting it up as a new drive, I just seem to be missing something.

by oh smeg

Run a RAM and a CPU Test here. If you don't already have this download yourself a copy of the Ultimate Boot CD from here

http://www.ultimatebootcd.com/download.html

You can boot off this and test all of the installed Hardware.

I would suggest using the 60 GIG HDD here as it will be within the BIOS Upper Limit of the M'Board where as the 160 [b]Will Not[/b] be. that is your main problem here. You can not partition the drive down as BIOS still can not recognize the full capacity of the HDD and incorrectly maps it causing Read/Write Issues to occur. The DLG Application is not addressing the BIOS Factor here it is just offering to clone the Old HDD to the new one and then running into a Problem with the inability of the M'Board to address correctly the HDD fitted here.

You should also slipstream a XP Install Disc with the Service Packs on them by using nLite from here to make your Install Image.

http://www.nliteos.com/download.html

With nLite make sure to rad the Directions listed in their Guides Page on their Web Site here

http://www.nliteos.com/guide/

Col

by shetech52

It is informative and hopefully helpful. Also, that makes sense about the USB drive ignoring the switch, but it shouldn't do that should it. It's a Sony USB floppy and it has worked fine drag and drop, but the WD DLG runs a set up program that saves to the disk and that's where I'm having problems. Does anybody know if the WD DLG programs are problematic, I've never used them before.
Thanks for the help.

This discussion is closed to new replies.