Discussion Locked

Unable to bring the PC on Lan

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi All,

I am having win98 peer to peer network using switch.the problem I facing is one of my Pc is unable to come on Lan .I have change the lan card and change the cable also.still I am unable to bring it on Lan.Total network settings are also correct and verified.I am thinking it might be problem of motherboard I have tried on various slots of the pc.but still unable .can someone plz provide me solution.

9 replies

by an_it_guy

Assuming that its a TCP/IP network, I would suggest you try to verify that the networking is installed properly on that pc, usnig the 'ping' utility. Try pinging the following:
1. ping localhost
2. ping local_machines_ip_address
3. ping any_ip_over_lan
In any cases if u do get "Destination host Unreachable" means the configuration is not correct. If u get "Reply timed out" the physical connectivity of the machine is not OK-like cable, network point, port on hub/switch faulty etc.
Hope the Workgroup name specified matches all others on the peer-to-peer network.
Hope this helps.
Cheers.

by opatzg9

I don't know if this helps or not, but you could try a cross over wire and skip the switch to see if that peer to peer is working and thus put the blame on the switch. Otherwise, Recheck work groups to be the same, DNS, and then pc card ip address should be at least 1 in difference between the machines, might even change it more.
Same protocols on other machine. Other than that you've already tried another lan card, and different slot so you're running out of solutions fast. Are there more than 2 machines involved here with a pair working so you know the network settings are right? Otherwise there are a number of good articles out there on setting up a home network, download and print up one of those and start the process over. We could probably use a little more information, what network cards are you using, whats the pc thats failing architecture? Good Luck

by rcom

First I seriously doubt it's the motherboard.

Since you've experienced the same problem with 2 network cards I'd uninstall everything in network properties. Plus open add/remove programs and uninstall dialup networking from the windows setup/communincations/list.

Now reinstall but keep it simple, just install client, adapter, protocol and sharing. Should look like this;

Client for Microsoft Networks
Network Adapter
TCP/IP
File & Print Sharing for Microsoft Networks

Please re-check the settings for the network.

WORKGROUP: obvious, check spelling etc.

CLIENT: windows, remove others

Adapter: Is it set to auto-detect the speed and bound to the correct protocol. Is there conflicts in device manager with other deivices?

Dialup adapter(s): as mentioned remove til connected

PROTOCOL: what is the protocol? remove others like IPX/SPX and netbeui.
If TCP/IP, is it matching the rest of the network? DHCP, DNS (hostname, domain, primary & secondary server IP), Is IP addressing within the same range(example 192.168.0.1), is there a matching subnet mask (255.255.255.0)
If using a gateway is it correct?

Are you using firewall software? Has outgoing & incoming been allowed for the network adapter.

As mentioned can you ping the internal/loop address 127.0.0.1 or any of the others on the network.

Disconnect one of the working PCs and input those exact same settings on the PC with problem.

by robinarm

Firstly check if there is a light on the NIC. There should be a glowing LED showing its working as far as getting power. Next plug it into some else like a hub. There should now be another LED showing conection. If not try the NIC in another computer and another computers NIC in your one. That should find any hardware problems.

Next try using a crossover cable or a crossover socket and connecting directly to another pc which does work on the LAN. Does that work? Also look at which ports you are using on the switch. Some types have an uplink port which you can use to link directly to another hub. This is in effect a crossed over port. You can't use this port and all the others at the same time - check the Hub documentation for details. Try only using ports 4 & 5

Next check the speed of the NIC's. If your card is a 10Meg card and the others are 100Meg they wont see each other unless you are using a autosensing dualspeed hub. That is a hub that can pass packets from both speeds to both speeds at the same time. Some hubs are "10 or 100meg" and not "10 and 100meg". Even if your is proper dual speed it may still be the problem. These hubs actually have two circuits with a single very fine joint connecting them. This joint can fail so each circuit is not in electrical contact with the other - one device two hubs. Try setting your problem card to 10meg and another to 10meg.

Assuming you've looked at IP problems check you host files on the client. Find *host.* and delete "hosts.sam" "lmhosts" & "lmhosts.sam" and edit "hosts" and put in some IP's. If you run a domain put in the PDC with the #PRE #DOM:xxxxx part and put in the WINS or DNS servers too (see the example hosts file for info). Copy the hosts file to "lmhosts" and reboot. This should allow you to ping these servers by name.

If it still doesn't work repost your query with updated info of what youv'e tried.

This discussion is closed to new replies.