Question Locked

USB 2.0 combo card installed, works except for my wireless kb/mouse combo

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I have been trying for days now to figure this out on my own and decided I better ask for some help.

I have a computer at home which still had the USB 1 ports-2 in front and 2 in back. The 2 in back are coupled up with my lan jack.

I recently installed a brand new PCI combo card with usb 2.0 and 1394 connections. And I also connected a usb 2.0 hub for my peripherals.

I connected the PCI card and Windows XP recognized the card as well as the hub.

But my brand new MS Natural Ergo 7000 transceiver for my kb and mouse will not work if I plug it into the hub or a port on the card itself.

If I plug it back into the front usb 1 port it will work.

I went into the device manager to look over the USB connections and I looked at the kb and mouse info in the control panel.

I cannot figure out why the combo seems to be designated.

I even deleted the Composite USB driver but that did not help. I also had unplugged the front USB from the motherboard and restarted the computer and still no good!

I want to take out the front usb 1 ports, try to disable the rear usb 1 ports and only use the USB 2 pci combo card in conjunction with the hub. All my peripherals are usb 2.0 compatible and I have plenty of room to plug them all in, so the usb 1 ports are useless to me.

Any idea at all how I can fix this? I had also written the manufacturer of the pci card but have not received an answer as of yet.

7 replies

by oh smeg

After all I do not believe that you can type faster than a USB1 Port can accept incoming data so what are you achieving?

By all means move the Data Intensive devices to USB2 but forget about the Keyboard/Mouse as they don't need the extra speed that USB2 offers.

After all if you disable the USB ports on the M'Board all you will have achieved in doing is leaving an opening to suck in dust and other junk to get dirty and possibly shorting the life of the M'Board so what are you achieving?

Col

by pcaddict

Hi OH Smeg,

I was only trying to have the USB 2 ports the only ones accessible/using any juice on the computer as I see they automatically take 10% w/o even being used. Also, it would help for me to reference.

But no matter what, there is still an important issue being ignored here. If my kb and mouse are working on a USB 1 port in front of my computer, then WHY doesn't the transceiver work in the rear on the new USB 2 ports? Afterall, it was geared toward USB 2...
Generally from my experience, a USB port is a USB port and you can stick your printer, scanner, fax, camera etc in ANY port and it will still work...so why not this combo??

Also, as for more holes in the computer...well the face plate has been off for a couple years now, I am often removing the side panel to get inside-especially now that the rear fan is going out and I have not replaced it yet, I keep the side panel open for now. I have plenty of canned air and so on LOL It's barely the computer it started out to be anyway.

I am planning on building a new computer this year and all the new junk I put on this one will go to the new one I build. And USB 1 ports will not be making the transition.

So I know where you are coming from and I appreciate it, but I am really trying to troubleshoot what the issue is and how to fix it properly.

by computercookie

software that came with the devices, I'm talking about the PCI USB card, the KB and the mouse.

If the KB and mouse still don't work it means you have a problem with the USB card drivers and you need to check in the device manager to see if the USB ports are working !

by oh smeg

What I think is happening here is a Chip Set Issue between the USB Card and the Transmitter for the Keyboard/Mouse but that's a Best Guess and nothing more.

However the M'Board mounted USB Ports can supply more power than anything else so there may be a Current Issue here as well because the PCI slot has limited Power available to it and hence the USB Ports that are on it. As you quite rightly say the On Board USB Ports take 10% of the power and possibly more in a underpowered system to drive any USB Devices that are plugged into them. These have more Current Available that any others to drive things and I think that is playing a part here as well. So while a USB is a USB there are some minor differences between them the main one being the available power that they can dish out. This is also quite important to any High Power USB Device.

However if it is a Current Issue which it may well be the Plug In USB card will be way behind the 8 Ball every time.

Incidentally the Rear Fan is that the one in the Power Supply? If so replace the Fan now at the very least as once the Power Supply starts to overheat it becomes unstable and the Voltage output & available current can swing wildly damaging the computers components.

Col

by pcaddict

Hi,

Ok, long story short, I called the manufacturer since they were not responding to my e-mail. They also said too much power being pulled from the USB hub, had me disconnect everything AGAIN and plug only the transeiver for kb/mouse combo into their pci port directly. It again recognized there was a 2.4 MS transceiver...and again wanted me to install the drivers. So I connected my PS2 kb and mouse and installed the drivers. The only problem is it KEPT asking me to do this!!! So then I also installed the included software AGAIN as well. The 7000 works perfectly fine on the HUB WITH everything else plugged in!!!

I really did not believe I was pulling too much power and here's my reasoning. I could not accept the fact that a printer, external hard drive, scanner, web cam and hub could ALL be working at the same time AND equal less than ONLY the 7000 running on the port. Also, the hub is set up so that if you are pulling more power than a port is capable of, then the little green light goes out to show this.

OK...so here it is: I have everything plugged in, I am right now using my 7000 and all is fine..EXCEPT:

When I was snooping around device manager, network connections and so forth...

I noticed in network connections which I have 2 icons btw...I have Local Area Connection and I have 1394 connetion.

Well..now the 1394 connection says #2 why??

Then, when I start my computer, it says connect keyboard/mouse and restart.

SO this tells me, I need to set "SOMETHING" somewhere that either bypasses looking for the PS2 mouse and PS2 keyboard...or I need to change something that recognizes the Composite USB connection as the startup for kb/mouse...but I have NO clue what or where.

I was thinking in the BIOS area when you reboot...or services, or msconfig or...but I personally do not have a clue where. I left my computer on all night and was able to wake the computer by jiggling the mouse which is a setting I chose in the mouse settings...so it does work...just I have a startup issue I need to fix...

Any clues for this?

Thanks Again!

This discussion is closed to new replies.