usb flash drive
hi
my usb flash drive will not be visible in My Computer
Hardware
hi
my usb flash drive will not be visible in My Computer
by arlcher Accepted solution
by rob miners Accepted solution
{1}
Try rebooting the computer without any USB devices attached. Then plug in the USB drive, right click on My Computer, select manage, and then click ?Disk Management.? If the drive is not present in the Disk Management window or if you are not able to access it, then the drive may have failed. In this window you should see all of your connected physical drives, their format, if they are healthy, and the drive letter.
Change the drive letter of the drive. Right-click on the drive in the list, and from the resulting menu select "Change Drive Letters and Paths"
Click on Change so you can change the drive letter. Click Change. Select a new drive letter from the drop down list, preferably the one that is not normally used for this drive.
Click Yes on the confirmation screen and you are done.
{2}
Write down all fixed Disk and CD/DVD drive letters so as not to delete them. DO NOT delete any of the fixed hard disk drives or CD/DVD optical drives registry values.
1. Login with Administrative privileges.
2. Disconnect all USB or FireWire storage devices.
3. Open Registry Editor by typing regedt32 in the Run box and navigate to the following registry key: HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices
4. Under HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices there will be registry keys with the name that resembles the format of \DosDevice\X: where X can be any alphabet letter which corresponding to your physical system drive letter.
5. Delete all possible USB drives, FireWire drives and external drives which have a drive letter.
DO NOT delete any of the fixed Hard Disk Drives or CD/DVD optical drives registry values.
Exclude \DosDevice\A: which normally reserved for floppy disk drives.
{3}
Click Start and in the Run box type in cmd and press Enter.
At the command prompt type in chkdsk U:/r 'the drive letter that you just added:' EG: U: and press enter.
If it finds any discrepancies it should fix them.
Tip: The cause of unpredictable behavior in a USB drive is often found to be the incorrect removal of a previously connected USB device. When removing USB devices right click on the ?Safely Remove Hardware? icon in the menu bar tray. This is usually found in the bottom right hand corner of the monitor. Once you have clicked on the icon, a menu with a single selection should appear. Click again on that selection to see the ?Safely Remove Hardware? window. Select the correct USB device and click the ?Stop.? When you receive the message that it is safe to remove the device, unplug the USB device from the computer.
{Note}
Most External USB HDD devices are delivered with two cables (a Data cable and an addtitional USB Power cable). If you encounter problems, use both the Data and Power cable.
If the External USB HDD devices still fails connect it to a self-powered USB Hub.
Most problems on an External USB HDD devices are caused by a too high power consumption during initalisation or data transfer. The USB specification for a USB port is 500mA per port. If a device needs more then 500mA, the USB port may be switched off by the over current circuit.
To avoid too high a power consumption on the used USB port, connect the External USB HDD device to a second USB port with the additional Power cable . This provides up to 1000mA to the USB device. If the device still fails, try a self-powered USB Hub, as they are, in most cases, able to provide more than 500mA per USB port.
If all this fails, you may have to check if the USB ports are Ok (i.e. possible Hardware failure). To check the USB port, connect a generic USB device like a USB mouse. If the USB port is Ok, there may be an incompatiblity between the system and the used External USB HDD Device. If so, try a different device or one from another vendor.
by deadly ernest Accepted solution
for instance -
A win 98 system requires extra drivers to be loaded before it recognises USB devices.
Points to check is the relevant services etc in the OS are activated to allow automatic recognition of USB devices, any special drivers for the device are loaded, the device is compatible with the USB hardware (an older board with only USB 1 will have a hard time finding a USB 2 device), the USB internal leads are plugged in to the USB headers properly, the USB auto detection is turned on in the BIOS.
You see, all these are possible issues as we don't know if this is the first time you tried to use a USB device on this system or not and other critical information.
This discussion is closed to new replies.
Sort by Trending