Question Locked

USB Flash Drives,PenDrives Doesn't Work.

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have p3 800 MHZ with intel 810e motherboard. I had tried jetflash , cruzer pen drives but none of them has been detected on my system. I'm able to use adsl modem from the usb.

I have OS win xp sp2.
In BIOS i have only option USB Controller (Enable/Disable) i had enabled it.

Can anyone tell me what to do make ?.

Please help me.

Regards,
Pul_mal

14 replies

by w2ktechman

is to look in drive management and change the drive letter. If it does not show up in there, it may be disabled function to allow these drives

by hal 9000

So I would look at the Computer Management/Devices and make sure that the USB Drivers for that M'Board are actually installed if nothing else in the way of USB Devices are working.

If you have other USB Devices Working it has to be something with the Jetflash devices being the problem.

Col

by w2ktechman

" I'm able to use adsl modem from the usb"

But good advice none-the-less

by hal 9000

I must be going nuts or maybe the other USB Socket is damaged and no longer active.

I've seen that a couple of times now where someone who is fiddling around at the back on a PC manages to break the USB Socket.

Col

by imagictech

I have had a similar experience when i have connected a USB drive to a system that had additional drives or network drives connected. In a case like that, there may possibly be a drive letter conflict. when it is plugged in right click on my computer and select manage. select disk management and look for your volume there possibly a volume without a drive letter assigned. Of course i failed to ask if the drivers had installed or if it went throuh any kind of plug and play detection - silly me. I should also ask if you get any kind of indicator light on the drive when you plug it in.

by imagictech

I failed to read the first posting on this string. I didnt mean to be redundant on checking the disk management mmc.

by w2ktechman

it also helps to verify a troubleshooting technique if multiple answers are the same.

by w2ktechman

I had a power-outage. When the power came back online 1 USB port worked fine (front of the case) the other died. But it didnt even leave it at that, it took out mu USB hub and mouse, Luckily my printer was off (color laserjet) and my camera was unplugged.

by hal 9000

That's why I have a Surge Protector in the Fuse Box for just this one power point and then have everything on UPS's but even then I unplug everything the moment that there is a Thunder Storm or a Power Outage.

Even though the Surge Protector is supposed to stop a Lighting strike at 100 feet I'm not willing to test it out with my hardware. :D

Col

by jordanspcrepair

Make sure you have the Logical Disk Manager Administrative Service and the logical Disk Manager Service are both enabled and startup automatically.

for an easy access way to do this, click Start, click Run, and type in "services.msc" without the quotations, and click ok.

by w2ktechman

but this was a non-critical system and the powerout was very unexpected. I heard a crash, and the power went out in a few seconds.

But I agree with UPS's, I have 5 currently in my house, all are larger than needed. Last time the power went out the SW told me I had 4 hours to shutdown my system -- lol

by group116

I had tried with jet flash 2 gb drive. After plugging it's gives me it's HI-SPEED device you need USB HUB for that.
Whether i need a driver or whether i need to add any hardware for that.

Disk Management gives me error unable to connect to local disk managment service.

Regards,
pul_mal

by w2ktechman

The high speed device in a non high speed port error is because your comp has USB1 and not USB 2. This is not an issue because it should be able to read it still.
Since it is not finding it but it is detecting it, try plugging it into another system, can it be read from there, or does it need formatting?
Open Device Manager, is it showing with an exlamation point?
You may need to reinstall your USB ports, try updating the MB drivers, or, if seperate, try updating USB drivers.
Also, if that does not work, try blowing away all of your USB ports and re-installing them.

This discussion is closed to new replies.