Question Locked

VPN IPSEC tunnel problem cisco router 871 -> Symantec Gateway 5420

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a problem with a vpn tunnel between 2 locations. On one location is a symantec gateway 5420 installed and on the other location is a cisco router 871 installed. I have a certain connection but I get a message UP-No-IKE

Further I can't ping of do anything to the remote location.

The Symantec I didn't install some one else did. And I can't get any good information about that site of the tunnel. So I have to figure it out by my self. with a debug I get some information back but I can't get out of it. therefor this question

000502: May 12 02:57:31.101 GMT+1: %CRYPTO-4-IKMP_NO_SA: IKE message from x.x.x.x has no SA and is not an initialization offer
000503: May 12 02:57:52.979 GMT+1: %CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=x.x.x.x, prot=50, spi=0x67838264(1736671844), srcaddr=x.x.x.x

7 replies

by triathlete1981

the cisco router can't authenticate to the symantec "IPSEC packet has invalid spi for destaddr". here's a link for that specific product on cisco's site:

http://www.cisco.com/en/US/products/ps6200/index.html

you need more info from the symantec side. tell mgmt to shell out some cash for you to go to that site or get someone to be on that side while you're over at your side troubleshooting.

by cg it

might be that the Cisco appliance uses Tunnel mode therefore the entire packet is encrypted and the Symantec appliance isn't setup to decrypt the packet.

if the Cisco appliance uses IPSec in transport mode then the Symantec appliance would be able to read the packet header and forward to the destination host.

so the real question is, is the communications between the 2 points Endpoint to Endpoint? Host to Endpoint?

So I'd check the Cisco appliance to see what mode IPSec is being used. If Tunnel Mode, change it to transport mode and see if the problem persists. If so, then yeah, a trip probably is necessary or someone on the other end who knows the Symantec appliance that can help with the WAN communications.

note: the Symantec appliance with Stateful Packet Inspection will drop packets it can't read.

by tsjonge

I get at the moment an UP-NO-IKE message.
The symantec isn't configured by our company but by an other.

I have already tried some one from the other site. but they gave me less information.

IKE SA IPsec SA
Exist, inactive Exist (flow exists) UP-NO-IKE

during debuging vpn crypto isakmp i get a result of
No peer struct to get peer description

by cg it

the routers negotiate between themselves, establish and main the tunnel. Clients have no interaction in the establishment of the tunnel. They only use the tunnel to pass data.

So, if no tunnel is created, it's gotta be that either your router's IPSec secure communications negotiation and authentication with the Symantec appliance doesn't match or the other way round.

note: there is a method of IPSec that requests secure communications negotiation but does not require it. Another setting that requires secure communications negotiations or else no go.

by tsjonge

I have added a static route to the ip route table and since than i can connect to the other site. But I requested to the German if the would look to their site with my information. But haven't hear about it. The can work that is the most important thing. At the moment. I hope that the Germans will change some thing that it work fine. I can't change much I think and that is my opion.

It's for sure thanks for the help it helped me to change the this little thing in my config I think

by cg it

but the IOS is similar to all Cisco routers and VPN with IPSec endpoint to endpoint [gateway to gateway] all operate the same way regardless of mfgs so I just figured to suggest the obvious.

glad you got it working.

This discussion is closed to new replies.