Question Locked

Weird IP Address and Can't Get to Internet

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a desktop and laptop; the laptop is connected by wireless PCI card to my router. Desktop is connected by cable and works fine and gets internet web pages.

Laptop indicates it's "connected to the internet" and I can access files on my desktop from my laptop; but, I can't bring up a web page on my laptop.

I've tried ipconfig.... release, renew and what shows in Network Connections is my usual IP address. But, when I do ipconfig /all, it shows:

DHCP Enabled: Yes
AutoConfig Enabled: Yes
IP Address: 192.168.0.101
Subnet Mask: 255.255.255.0
IP Address: fe80::211:95ff:fe04:6408%9
Default Gateway: 192.168.0.1
DHCP Servers: 192.168.0.1
DNS Servers: 192.168.0.1
fec0:0:0:ffff::1%3
fec0:0:0:ffff::2%3
fec0:0:0:ffff::3%3

This doesn't seem right to me; with all the alpha characters and colons... not a typical IP address.

I've gone through the process of down-powering modem and router, re-booting, etc. I've also removed and re-installed the network wireless PCI card on my laptop. All to no avail.

Can anyone tell me what's happening and how to correct it ? How can I get access back to the internet ?

Any help will be greatly appreciated. Thanks in advance.

17 replies

by cg it

the IP # you listed isn't hexadecimal which IPv6 uses [8 groups 4 hexidecimals].

by williamsmc

I re-checked and the information I put in my original post is exactly what I see when I do "ipconfig /all" , in the section for my wireless adapter.

There are no line items with an "IPv6" in them; however, I should note that the 3 lines containing "fec0:....." are each separate lines, and spaced over so they appear directly under the DNS Servers address. However, for these 3lines, there is no description of what they are; and they are not preceded by "...... :" like the previous lines with descriptions.

I'm not a "techie" in this area, so if you could explain it to me very simply, I'd appreciate it. Thanks.

by cg it

is noted in hexidecimal form.

The difference between IPv4 and IPv6 is how many bits are used. IPv4 uses 32 bits 10011001.10001010.11110000.00001111 [4 octets of 8 bits each]. IPv6 uses 128 bits [I'm not going to list out 128 1s and 0s which is why IPv6 uses Hexidecimal].

:: [double colon] means all zeros in the 4 digit set in IPv6. e.g 0000 = : 0000 = : or ::

Fe80 is IPv6 autoaddressing [APIPA ]and Fec are all IPv6 designations for local network only addressing. I've not run into % used in IPv6 so when I said it's not IPv6 it's because of the % character [as far as I know % isn't a valid character for IPv6].

by spidershrek

Make sure that your modem is not set to DHCP. Your router should be DHCP.

Most home modems IP are Dynamicly given by the isp provider (SBC, Comcast, etc.)also make sure you can ping both router and modem. Hope it helps!

by sgt_shultz

did this ever work?
did you do an ipconfig /all on the working desktop and compare? the dns address you listed probably is the problem. you might need to set that to the dns server address provided by your isp

by williamsmc

Yes, the laptop worked back in January... last time I used it.

When I compare the DNS on desktop and laptop, it is the same. However, under "DNS Servers", the desktop has no other lines under it (other than the date & time of lease); whereas, the laptop has those 3 additional lines beginning with "fec0:....".

by sgt_shultz

or how they got there. will it let you remove them? (the laptop 3 lines of weird dns numbers?)

by williamsmc

How would I go about removing them ?

Once I type in "ipconfig /all", it then lists all the information, but it won't let me move my cursor to that position.

Any ideas on how to edit or change them would be appreciated. thanks.

by cg it

it appears to be IPv6 addressing.

is the O/S Windows Vista? if so, Vista supports and installs by default IPv6 AND IPv4.

by sgt_shultz

i would try removing and reinstalling tcpip from Control Panel/Network and dial up connections, get properties of Local Area Connection. highlight tcpip then Remove. then reinstall.
if that won't work i do wonder if your router is on the fritz. you could set up static ip addresses by picking one say 192.168.1.50 use 255.255.255.0 for subnet.

i wonder if you isp is doing something on their end. you could try powering off the router for a couple minutes to force it to pick up new server setttings, maybe the short power down and back up isn't refreshing them...

by cg it

Shultz, the guy or gal posting says they do PC support. Now I recognized IPv6 addressing except the poster had a % character listed which to the best of my knowledge isn't a supported character. Now PC support means they have a exeperience and for the life of me I can't see someone in PC support not knowing at least the basics of IPv6 addressing. So I'm wondering about the questions validity. Especially the part about ipconfig/all and not being able to move the cursor to change values.

That's done in the NIC properties page and anyone that does PC support HAS to know how to do that else their not PC support and if they are, their jerking chains.

by williamsmc

I'm not trying to present myself as a computer "techie", nor am I "jerking your chain". I provide GENERAL support for engineers with PC-related problems. I am NOT a computer expert.

I guess I didn't realize it was critical to provide a detailed description of job duties and experience level in order to participate in this forum.

I apologize if I have mis-represented myself. Just consider me to be a "dumb engineer" who needs help and would appreciate any and all those providing such help.

Thanks.

by cg it

Techrepublic has their own group.

Personally, I make the assumption that if your here on Techrepublic, you have some technical competency in computers whatever flavor they may be. Techrepublic is after all "A resource for IT Professionals".

Your addressing is IPv6 or appears to be. Is this on a Windows Vista computer? If so, it's a simple matter of turning it off.

However even with IPv6 on, IPv4 is also on and you should have network connectivity.

by williamsmc

No, I don't have Vista; it's XP Professional. I checked and it is IPv6.

by cg it

only suggestion I can think of based on using Windows Vista which has IPv6 enabled by default, there was no internet connectivity, and all other factors that would effect internet connectivity were ruled out.

by sgt_shultz

as you know i have severe stupid seizures. so that is ipv6? news to me. to clarify, i was noting that with tcpip set to be dhcp client you can't change anything...can you? maybe you can change the dns. i really shouldn't try to answer these questions without xp box in front of me.
i thumped my bs indicator, i think it is working again ;>) thanks

This discussion is closed to new replies.