Question Locked

What is suitable GLUE to re-attach a laptop keyboard key ?

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Go on guys - have a good guffaw on me!

I'm beginning to hear the not-so-distant 'Death Knell' of my Acer 1363.

I've already had TR topics regarding this Acer:
1. The TSST 532L-A DVD-Dual drive is kaput. All current installs are accomplished via network link to a Toshiba-Seimens tower.

2. The Acer battery lost it's staying power about a year ago - can't rely on it for more than about 9 minutes.

3. The HDD is currently spitting out errors on EVERY boot. Copying of the PQ-Service hidden partition is currently underway for inclusion into new HDD.

4. I've now just witnessed my ' \ ' key come away attached to the pinky of my left hand!!! It's a pleasant looking little key, if thinner than I imagined it to be.

The nipple that now sits proudly where the key used to hide it, is a curiously-wobbly rubber affair. I'm beginning to feel guilty having repeatedly bashed this poor little nipple so, so many times over the last 31 months.

I was just going to grab my nearby supply of what we Brits call Super Glue - but then thought the acrylic content might eat the rubber nipple.

[b]Any thoughts?[/b]

As a side order question:

How long d'you reckon I've got before the TFT dies on me ? After all, it's the only component left that hasn't died!! :D

8 replies

by seanferd

No little plunger going through a hole (should I stop now) to depress the nipple on the pad?

edit: Maybe a tiny bit of semi-dried rubber cement, or one of those inner-tube/swimming pool patches, where you use a bit of raw rubber and some vulcanizing goop? Make sure it sticks to the key first. Maybe make sure the goop won't eat the nipple, test it on an extra nipple from some other trashed kbd (assuming the nipples are made of the same stuff).

by older mycroft

The nipple just seems to collapse down on itself, just like an erm ...nipple!

by seanferd

that is about all I can think of. What held it together in the first place? Was there originally some kind of glue or heat fusion, or does the key have some bit that gripped the nipple?

I'm kind of curious for my own sake here also, as I tend to pride myself on being able to rig up anything remotely fixable. Fixed lots of keyboards, even though they probably weren't worth the effort.

I'm edit again: Really sticky two-sided foam tape.

by older mycroft

Presumably directly with the nipple.

This is the weirdest type of contact I've ever witnessed. Clearly laptop keyboards are a lot thinner than a conventional clunky pc keyboard. Nevertheless, I assumed (obviously wrongly!) that the plastic clip'n'nipple affair would be just the same [u]but smaller[/u] - but there is just a little shiny circle where the rubber nipple would've been in contact.

The curious thing is that there was absolutely no noise when it came away on my finger - not a snapping, popping noise - nothing at all.

Oddly I'm finding the rubbing sensation on my finger to be quite stimulating.

This little nipple has taken on a life of its own - a bit like bubblewrap that you can't stop 'popping'!!! :D :D

by seanferd

Magic? Dark Matter? A little flange around the edge of the key that sat below the edge of the board surface?

Oddly enough, I've got a bottle of nipples, a whole keyboard's worth, from a -you guessed it- keyboard, that I took apart to clean, an haven't yet reassembled.

by thechas

Hello,

If the part of the key on the laptop is rubbery, I would use either adhesive grade silicon, (different from the caulk / sealant grade) or weatherstrip adhesive.

If the old adhesive has a slight yellow cast to it, it is weatherstrip adhesive.

The trick is to use just enough adhesive to bond the key, but not so much as to spread over the moving portion of the rubber.

Even if both sides were plastic, I would recommend not using super glue.

The best way to glue plastic pieces together is with solvent bonding that melts the plastic and forms a new weld between the 2 parts. Basically the way plastic model cement works.

Chas

by seanferd

Good call. That'll glue almost anything together. We just need to make sure we use a very small amount. :)

This discussion is closed to new replies.