So here the BIOS Shows the SATA Driver as a IDE Drive int he General Headings and lists it as something like IDE forth Master or Slave as the actual Drive here does it.
if it does then the M'Board natively supports SATA Drives but if it doesn't show the SATA Drive this way it doesn't Natively support SATA Drives. It supports SATA Drives through the application of a SATA or RAID Driver when you install the OS. If it Natively Supports SATA Drives you need to connect the SATA Drive tot he 0 or 1 SATA Connector not any other. You should always connect the Primary Boot Drive to the lowest Number Connector that the M'Board has listed. Look in the M'Board Manual for which SATA Connector is which. I had to reset a Customers ASUS M'Board earlier today to do this so it would boot to the stage where I could Install Windows. It does natively support SAT Drives but not when they are on the Number 4 SATA Connector you can not boot from that Drive.
Now for your Corrupt Windows Install on the IDE Drive you need to do a Repair Install with a M$ Branded Install Disc not a System Makers Recovery Disc as this option [b]Is Not Supported[/b] by the majority of Recovery Disc's.
Just follow the directions listed on M$ Knowledge Base Article here
http://support.microsoft.com/kb/315341
Teh important bit is this but you should read the entire Notice
[i]Prerequisites
Windows Installation CD
Before you start, have your Windows installation CD and the product key available. Without these, you cannot reinstall Windows. If Windows was preinstalled on your computer, contact the computer manufacturer for help in obtaining the Windows installation files and product key.
Device drivers
Many of the device drivers for your hardware components are integrated into Windows. However, devices such as printers, monitors, graphic cards, sound cards, modems, external drives, and scanners usually have separate installation CDs. If you do not have all the drivers for your hardware components, you can download the drivers from the Internet and then write them to a CD.
If your computer requires a third-party mass storage device driver or hardware abstraction layer (HAL), make sure that you have a copy of the files on a separate storage media before you start the reinstallation.
Internet Explorer 7
If Internet Explorer 7 is installed on your computer, you must uninstall it before you reinstall Windows XP. For more information, click the following article number to view the article in the Microsoft Knowledge Base:
917964 (http://support.microsoft.com/kb/917964/ ) How to perform a repair installation of Windows XP if Internet Explorer 7 is installed
Programs
Collect and store the CDs and product keys for your programs in an appropriate location so that you can reinstall the programs after you have reinstalled Windows. These programs may include the following:
Microsoft Office programs
Antivirus software
CD writing software
Internet Provider software
Data backup
Before you reinstall Windows, back up all important data to another location. Data that you may want to back up could include the following:
My Documents (documents, pictures, music, videos)
Program folders (configuration data, user data)
Favorites
Address books
E-mail messages
Document templates
Macros
Boilerplates
The original backup copies of your registry files (located in the %systemroot%\Repair folder) are replaced when the reinstallation is completed. These original registry files in the Repair folder were created either when you started Windows XP or when you last used the Backup utility to back up the system state. If you think that you might have to use the registry backups after the reinstallation is complete, copy these registry backup files to another location before you perform the reinstallation.
Network settings
You can restore certain network settings after you reinstall Windows. Before you start the reinstallation, record your computer's network settings so that they can easily be available if this step is required. These settings include the following:
Computer name
Workgroup or domain
TCP/IP settings
To find these settings, do the following steps:
To find these settings, click Start and then click Run.
Type control ncpa.cpl in the Open text field and then click OK.
Right-click Local Area Connection and then right-click Properties.
Record the network settings.
Internet provider information
To make sure that you can reconnect to the Internet after you have reinstalled Windows, record your Internet provider information. This includes user name, password information, and names of mail servers.
Startup sequence
Warning This procedure may involve changing your CMOS (Complementary Metal Oxide Semiconductor) settings and changing your Basic Input/Output System (BIOS). Incorrect changes to the BIOS of your computer can result in serious problems. Microsoft cannot guarantee that problems that result from changes to your BIOS can be solved. Change your CMOS settings at your own risk. Incorrect or corrupted CMOS and BIOS settings can cause startup problems or shutdown problems.
If you must adjust the BIOS startup sequence of your computer so that it can start from the installation CD, the sequence should be in the following order:
CD drive
Hard disk
Floppy disk drive
During startup, BIOS searches for a disk that has an operating system it can load. On a computer that has an operating system installed, this is usually the hard disk. The BIOS is configured to search disks on the computer in a certain order, called the startup sequence. If the computer hard disk is configured in the BIOS as the first disk in the startup sequence, the computer starts by using the hard disk and does not search the CD drive for a startup disk.
To configure the BIOS to search the CD drive for a startup disk before it searches the hard disk, follow these steps:
Restart your computer.
When the computer first starts, it performs the power-on self test (POST). This test checks that all connected devices are functioning. As part of the POST, the memory is checked. During the memory test, a message will appear that tells you how to access the BIOS. For example, you may see the following message or a similar message that explains how to start the BIOS setup:
PRESS DEL TO ENTER SETUP
In this example, you must press the DEL key immediately after the memory test is finished to start the setup process. You may have to press the key several times to make sure that you access the BIOS setup.
Tip There are other keys that may provide access to the BIOS. They include the following:
F1
F2
F10
CTRL+ENTER
ALT+ENTER
CTRL+ALT+ESC
CTRL+ALT+INSERT
If you are not sure how to access the BIOS setup, see the user manual for your computer's motherboard.
Look for the startup sequence settings (also known as boot sequence or boot order). You can usually use the arrow keys to move through the menus and settings.
When you find the startup sequence setting, you can usually press ENTER to modify it. Press the PLUS SIGN (+) or MINUS SIGN (-) key until the CD drive is selected as the startup disk.
Tip More information about how to modify the BIOS can be found in your user manual. It usually contains descriptions of the menus and instructions on how to modify the options. The BIOS itself usually contains context-sensitive Help with the individual steps.
As soon as you have specified the CD drive as the first location to search for a startup disk, you can usually press ESC to return to the menus. In the main menu, select the option SAVE AND EXIT SETUP or a similar option. When the confirmation SAVE TO CMOS AND EXIT or a similar option appears, select YES.
If you cannot select YES, type the letter y.
Note BIOS uses a QWERTY keyboard layout. If your keyboard settings follow a different layout, you will have to press the Y key as it appears on a QWERTY keyboard.
After you exit the BIOS setup, your computer will restart.
Make sure that the computer starts by using the CD drive. Insert the Windows XP installation CD and restart the computer. If this is successful, you can start reinstalling Windows XP. [/i]
Col