Discussion Locked

XP CPU Change Questions...

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am getting ready to change out the CPU on my custom built system. And i am trying to prepare for what problems this will generate. I am having a hard time trying to find out definitively how this will affect my system.

Will putting in a new CPU cause Windows XP Pro SP2 to no longer boot? Or will it just be re-authentication issues?

The only thing i am changing is going from a Socket 478 2.6 Gig to a 3.2 Gig EE. (Yes, my bios has support for this CPU.)

I have read differing things on what XP binds itself to for authentication. Some places say the bios, others say a unique CPU identifier, and still others list the NIC MAC address.

The reason why i am balking at your basic wipe and reinstall is that i employ a RAID 5 array that was extremely difficult to setup.

Any thoughts would be appreciated.

Thanks,

14 replies

by cmiller5400

As for the reactivation it is a combination of different hardware changes. I beleive that it uses a combination of all to generate a unique ID for your system, not just one component. Now as far as the CPU change, you should be fine as long as you set up the new motherboard for it (make sure it is supported as you state, make sure the clock is set right, etc.) It may trigger a reactivation, but that is a minor pain to deal with compared with a rebuild. You should just double check to make sure that you do not need to change any jumpers on the mainboard. But other than that, it should be painless. Good Luck!!

by zlitocook

The only problem that I had with Microsoft was when I did a warrenty replacement of a motherboard and CPU. After boot up it said I had a pirate virsion of XP, I called and had to talk with three people and had to send them the emails from HP about the warrenty replacement. And this was a corp. version too.

by thechas

Changing JUST the CPU should have no impact on Windows XP booting or Activation.

You need to change at least 2 items that are on the activation list at the same time to generate an activation event.

What may have some of the resources you checked confused, is that changing out the entire motherboard, or moving the hard drive to a different system can cause XP to not boot up, and almost certainly will cause an activation event.

Go ahead and change your CPU with no Windows or activation concerns.

Depending on the age of your system, you might want to install a new fan at the same time to improve system reliability.

Chas

by ozi eagle

Hi,

If you are only changing the cpu there should be no problem.

I have successfully replaced mobos and cpu's,in XP machines, when they died, with a new cpu - mobo combination, using the SAME BRAND of support chips, eg VIA. The drivers appear to be sufficiently compatible to allow booting and then updating the drivers.

by hal 9000

All that should be required is to shut down remove the power lead open the case and remove the Heat sink/Fan lift up the Lever and remove the old CPU. Unpack the new CPU and fit it to the 478 Socket and lock the lever in place Very carefully fit the new Heat Sink Fan as they can prove a bit hard to fit if you are not careful and close up the box. Then plug in the power Lead and reboot.

When you get to the Post Screen go int BIOS and make sure that the new CPU is being recognised. Exit BIOS saving changes and then allow the system to boot. Provided that this is the only thing that you have changed recently there is nothing else to do.

Windows will not ask for anything at all unless you have changed 2 items previously to changing the CPU if that is the case then you will be asked to reactivate Windows and if that happens forget about attempting to activate over the Internet use the phone it will be faster and less painful.

Windows should only ask to be reactivated when 3 items have been changed of course if you have made more than 3 changes in one hit you'll be prompted to reactivate. But if it's just the CPU and nothing else has recently been changed there is nothing at all involved.

Cheers and enjoy the extra processing power.

Col

by matt

Thank you all for the help. I bought a 3.2 Ghz Extreme Edition P4. My Asus Mobo specifically released a bios rev to handle the 3.2 & 3.4 EE. This being one of the fastest processors i can get for the Socket 478 should prolong my upgrading for a bit longer. I've invested in a very nice AGP Video Card so i don't really want to go to a Socket 775/SLI setup just yet. And since i custom build my stuff i generally stay behind the curve to save money.

Thanks again.

by jon

I recently replaced a dead CPU and I was forced to re-activate...which I had to do over the phone.

This discussion is closed to new replies.