Discussion Locked

Bad Sectors on Harddrive

0 helpful
31 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi it's me Derek,

Okay I got a harddrive with bad sectors that Windows won't let me boot up with it. When I booted my PC with another harddrive I found out that I could still see and read the data in the original harddrive. However the harddrive with the prob won't boot up and while doing the scandisk the scandisk program hanged at about 3% or 17% progress.

Is my harddrive gone? Is there a method where I can windows to ignore the problem. I plan to format taht harddrive and use it to install Windows NT ?

31 replies

by grosseholz

If you run scandisk make sure you run it without autofix. That can help because it gives you the option to correct faults as you see fit.
If you want to copy your drive Norton's Ghost is good, it ignores all but the worst faults.
Sometimes bad sectors are software generated and can be removed thru fdisk.
Be sure to backup first.
Rolf

by dmiles

The hard drive is not gone,and answer #1 gave good info,only I would not ghost a hard drive with bad sectors,you will ghost the bad sectors and tranfer them if you do this.
You may want to try booting from the ERD,if there was one created at setup.
Do you necessarily need the data on the hard drive is the question you have to decide.

by bdgray

Are you running scandisk in Windows? Boot to a Windows floppy boot disk and run scandisk from there. Also run a surface scan so that bad sectors will be marked and not used by the O.S.

You should realy consider just getting all of your vital data off of this HD. The drive is only going to get worse from this point on.

by calves

I am surprised that nobody mentioned Norton Disk Doctor, you can probably download a trial version of Systemworks and fix your disk.
I hope it helps you!

by seanw

The bad sectors on your drive have little or nothing to do with it not booting. The master boot record on the disk is gone. This is very easily fixed. Boot to your startup disk(floppy or cd). At the a: prompt(or where your disk is) and type fdisk/mbr.
This will replace the master boot record. Make sure your startup disk is the same as your OS.

by patrick

When you decide to format your drive I have repaired most problems using a small freeware program called shiva.
during the format process shiva will blank each sector then write each sector with ones and rewrite each sector with zeros the finaly blank each sector.

by jkozura

I have had a few hard drives that have developed bad sectors, and I have found only one sure way to cure the problem. Use Partition Magic to move the bad sectors into an unused, unformatted partition. That way Windows will definitely skip it. Otherwise, you may want to look at Spinrite from Gibson Research. I know either will cost a little, but you will be getting an excellent tool for the money. I have used both with excellent results. Sorry there is not an easier answer that will be reliable.
Thanks,
John Kozura IV
IS Manager
AICPA/PDI

by igp

Try to "resize" your disk with FAT system (with Partition Magic).

And, btw, did you scaned your PC for viruses? Some viruses write themselves to sector and then mark it like bad.

First that you can try is this: with DiskEditor change FA-FF (hex) of sectors on your hdd to 00-20 and run scandisk/ndd.

Sinserelly yours, Igor

by billygilbreath

> ...booted my PC with another harddrive...could still see and read the data in the original harddrive.

Sounds great, Derek!
My recommendation is to do that again and back up the data that you want to save (if any) from that hard drive. Next, to the Web site of your hard drive's manufacturer to download the low level format utility specifically designed for your make and model of hard drive. Using this low level format utility gives your hard drive the best possible chance for recovery. After the low level format, simply FDISK, FORMAT and install your operating system as usual.

by prubiola

Derek,

From your description, I gather that what is happening is that when you try to turn your computer on it starts booting into Windows (95 or 98) but that it gives you a message that the computer was not shut down properly and needs to run scandisk and while it is running scandisk the computer hangs. What I think you want is a way to keep scandisk from running so that you can save data before doing your NT install. If this is correct, then the way to get past scandisk is to edit the MSDOS.SYS file. In order to do this, you need to:

1. Boot from a floppy drive to a dos propmt.
2. at the dos prompt type:

attrib -s -h c:\msdos.sys

3. Use your favorite dos editor to edit the mddos.sys file, which should now be editable.

4. Find the line that begins: AutoScan=1. AutoScan is a directive to Windows to run scandisk. To turn this off, make it read: AutoScan=0.

5. Save the file (msdos.sys)

6. Type: attrib +s +h c:\msdos.sys

7. Reboot.

This should get you past the

by ryan

get a WIN98 Boot disk and run scandisk. It will ask you for each sector if you want to recover or ignor each sector once you ignor that sector is not going to be used. This is good to do if you are planning on using the disk further. You find it alot on laptops that are used to being Disk thrashed. good luck

by bgridley

Because you can not "boot" from the drive but can boot from another and then read the drive I would suspect a bad FAT / Master Boot Record. Try running FDISK /mbr from the A: prompt.
If this does not do the trick I would salvage what data you can from the drive and then perform a low-level format. I have done this quite often with great success using a utility available on Western Digitals web site.

by emmab

I swear by Norton's Disk Doctor. It will do a thorough scan of the drive and mark any bad sectors there may be. It will also attempt to move any data that might be stored in those sectors to a "safe" area on the drive. You can do this with damaged floppy disks. Also, how old is the drive? If there are too many bad sectors and it's reasonably new, the manufacturer may replace it.

by gdm

Sounds like your Master Boot Record is shot. Possible trojan virus as well
fdisk /mbr to reset your master boot record and virus scan the disk

by thedrummer2006

Ok first, if you are getting bad sectors it is never a good thing. It means that the data on your drive is decaying. Bad sectors form from a section of the drive being written and rewritten to constantly. The hard disk is magnetic so the magnetism in that area is jumbled. It sounds like there is some data that pertains to your operating system on one of these bad sectors causing your drive not to boot. You need to copy your info off of that drive immediately and do a low level format on it. RePartition the drive and you should be able to use it.
After that keep an eye on it. If it starts to randomly generate bad sectors it has probably seen its better days and is going to quit on on you one day. I have had experience with this.

Good Luck.

This discussion is closed to new replies.