Question Locked

Begins Loading XP and then screen goes black

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My first post and I apologize if anyone before me has asked this question or brought up this topic. But, here I go anyways. My computer last night was working as far as I knew, I had no problems with it. When I woke up this morning, after shutting down the pc last night and sleeping, I turned the computer back on and it posted fine, no problems there, and it appeared to start loading Windows XP Professional Edition. When it showed the loading bar, it would proceed to load for 5 seconds or so and then the screen would go black. The monitor is just about brand new, I think 2 weeks old or so and its been working fine.

I was told by jdclyde to create a profile here because everyone was helpful and usually "trip" over each other to answer questions. I do not claim to be a IT professional, but an IT novice. If anyone would be able to assist me I would more than appreciate it.

27 replies

by imperiel

I am able to start the computer up in safemode and it works that way, but other than safemode, it does the same thing.

by jdclyde

did you try a different video card, junior?

Maybe while in safemode, reinstall the driver? They do get pooched.

Have you tried booting to last known good conf?

This is NOT a new install, correct?

If the video works in safe mode, you know your monitor is fine. Try the driver re-install and let us know if that made a difference.

by imperiel

No changes have been made to my system other than downloading LotR:SoA. Oh, and the microsoft one-touch. I tried to not only reinstall the driver from cd but it ran into an error that gave me the message "End Program- you should not see me". I went online to nvidia's site and grabbed their updated driver and installed that version and it is now up and running again. Why would a driver pooch itself? It's not clicking in my head.... I did not try the different video card because i don't have a video card that has a dvi connector other than the 7950 GT. Last known good conf. also didn't do anything, tried that about 10 minutes before you post here.

by sgt_shultz

because your symptoms match problems with boot files but since you can start in safe mode you don't seem to fit that...
but since we don't seem to be falling all over ourselves with your answer yet you could defrag while you wait.
how is your antivirus, antispyware protection? have you scanned with updated definitions just so we can rule it out?

by imperiel

Did a defrag the last day it was working. Also did my anti-wares scans the day prior to the no video. I have a 300Gb hard drive but approximately only 12Gb are taken up so it was a quick scan. Even did the microsoft one touch thing they have on their website.

Antispyware- Spybot S&D
Adaware SE

Antivirus- Norton (forget the edition)
Microsoft's One Touch

by davedxb

If you can logon into safe mode.

Means the hardware is fine.

Im sure its the driver issue!!!!!

Sometimes, if you dont install the correct driver, the resolution is to high or low for the monitor...and the monitor wont read the graphics cards details giving u a blank screen.

Happened to me before. I fixed it by downloading the latest update for my graphics card from the Internet on ANOTHER computer.

The i logged into safe mode and copied the updates and installed them..

I strongly beleive its your driver files....funny how it work last night...maybe u updated windows???? or something??

by sgt_shultz

maybe a windows update was applied. or maybe you plugged in a new device a few days ago?
your symptoms sound like a boot 'hang' which could be video driver associated but could also be some other problem. you could also try unplugging stuff, especially wireless mice

by imperiel

Did all windows updates two days prior to this. Computer has been turned on and off several times since then without any problems. I don't have my computer setup to install the updates when i click shutdown.

by tink!

One of our PC's is doing the same thing. I am currently running a virus scan under safe mode. But last good config, and System Restore did not fix the problem.

I will let you know if I get ours to work again. (There was a Windows update on it last night but I cannot find a removable update with yesterday's date.)

by tink!

Our problem may not have been the EXACT same as yours... Ours didn't go black but rather sat on the blue screen right before the logon is supposed to show up. It would do that during any type of startup except for Safe Modes.

What I ended up doing:

Inserted the XP Windows CD
Booted from CD
Hit R for Repair
Selected the current install of Windows to logon too
Entered Admin password
and once the C: prompt showed up type "Fixboot" and answer yes
Restart

Of course, as an afterthought I probably could have done the same thing a lot quicker by booting to a C: prompt and then renaming the boot.ini file. Ah well. It's working now That's all that matters.

Oh...after restarting run msconfig. You'll want to select the selective startup and checkbox the win.ini, startup files etc. Just be sure to leave the boot.ini on original.

by sgt_shultz

hey were you able to boot in Safe mode when you were having this problem?

by imperiel

My video card is a 7950 GT 512 mb graphics card.

by tink!

The only boot that WOULD work was Safe Mode..with and without network support.

by kapakmerah

I have same problem like you, begins Loading XP and then screen goes black, when i restore to last restore point in safe mode, windows will go normal, but it just for while. The day after restore, screen goes black again. My friend in the same department in my office have same problem too. We use the same processor : Intel LGA Pentium Dual Core.

by lghtanddrk

I have a weird problem that happened once a month ago and now has been happening consistently for the past few days. Previously, if I shut my computer down when it got to "Saving your Settings" it could take up to about 30 seconds. Now it seems like it's just a few seconds like it's not really saving the settings.

The problem I'm having is that if I turn my computer off for a few hours and come back it boots into Windows fine but if I leave it off overnight and boot the next morning I have problems. Just after the Windows logo appears the screen goes blank like someone disconnected the VGA cable and the hadrd drive no longer runs. I have to do a hard reboot. Then I get the screen asking if I want to boot with my last known good configuration. This used to work a few days ago. Now if I choose this option I just go into a loop back to the same screen. The only way to successfully boot is to go to Safe mode and choose a System Restore.

I use Microsoft OneTouch Care and scanned for viruses and adware. Nothing. I scanned with Spybot. Nothing. I did runk CHKDSK and it found a bad file in MYDocuments that it fixed and nothing else. I have defragged succesfully.

I went into my bios config and turned off all other hardware so it boots to my C: drive only. No conflicts show in the Windows Device Manager.

I have AOL 9.0 VR and ran the Computer Checkup utility and that didn't find anything either. I ran MSCONFIG and made sure nothing odd was running in the background too.

I have all the latest Windows updates. I have Windows XP Pro SP2. I have an ASUS motherboard with a 3.0 GHz P4 w/hyperthreading, 2 GB RAM, and an EVGA 7800 AGP card. I also have an external 400 GB Maxtor connected via USB which I had a weird problem with one time. I had turned it off and my computer wouldn't boot until it was on. It's on this time so that shouldn't have had an impact.

The only recent software that I can recall putting in is the new Nero 8, the latest version of DVD Fab and the latest NVIDIA drivers (I just reinstalled the latest NVIDIA drivers again). I have been keeping my computer on for 3 or 4 days in a row lately before shutting down occasionally so I'm not entirely sure when this started happening. I think it's been consistent post Nero 8 which is the latest "big" change I made but I'm certain this problem happened that one time before installing Nero 8.

I opened the case to make sure all connections, etc. were seated properly.

I'm now forced to keep my computer on longer. I know some people will say it's better to leave it on because shutting it off more frequently is no good for the power supply but I am away on occasion and don't like doing that. So now before having to do a shutdown overnight I do a System Restore Save Point and cross my fingers that Safe Mode will let me back in and restore the next time the problem happens.

Previous posts have mentioned booting to the XP CD and using FIXBOOT in the recover console. Can this have any ill repercussions? In other words, if this is not the problem will it create one? Will it change anything if there is not a problem? And if it does fix something (assuming all gets corrected properly) should I be able to then just boot into Windows as normal?

Any ideas?

by jdclyde

It doesn't. Windows does it FOR it.

That is the price you pay for "ease of use" and "Plug and pray". The more automated something is, the easier for it to break.

by yeayea

torso lolz eatin yo momas cookin i spit it grandmaster slamed yoface boxer

by davedxb

You can use MSCONFIG

Log in SAFE MODE

sTART > mENU > Run > msconfig

and then choose:

"Diagnostic Startup - load basic devices and servicesonly"

This should start windows normally with only needed startup files.

If it runs like this...then definitly its a driver issue. Because when you start it like this, windows loads only the minimal files it needs in order to operate.

You can see what files load up with windows using a freeware program calle "autoruns"

very usefull. go to google and type "download autoruns"

You be able to download it from the microsoft site when you google these words.

Run it in safe mode and look in the LOGON tab...that shows you everything that start with windows...from there try to minimize what starts up....usually u can safely uncheck them all.

by imperiel

I'd like to thank all of you, including the most recent people to post, for your help. With all your help i was able to fix my computer (about two months ago, lol) and it has since then been up and running smoothly.

Thanks again everyone.

by wesley.chin

Were there any error messages? For me, when that occurred, it was cause hal.dll was corrupt.

by lghtanddrk

No error messages. I'm going to try tip above with the recovery console but shouldn't I choose FIXMBR and not FIXBOOT.

by lghtanddrk

FIXBOOT did nothing. FIXMBR saw that there was something wrong and repaired the boot sector but the problem did not go away. If the computer sits off overnight I can only boot back up by going into safe mode and then doing a system restore.

by iceinsidefire

Hey guys,
I had the same problem of blank screen on boot up / start up (use of these 2 words will help others in google search ).
It works in safe mood.
so I change it to selective mood in msconfig
and it work in normal mood.

I stumble upon the cause of my pc problem when saw the clock in CMOS. it shows time 1 jan 2002.
No matter how much i try. when pc shut down. it goes back to same.
So i change the CMOS clock battery cell and my pc works in normal mood with normal start up service instead of selected.

I suggest you also check, if same problem with you.

If this helps you also then in return, do favour with 2 people in your life and ask each of them to do favour in with other two person.
:)

by older mycroft

And prevent any misunderstandings like I have just encountered !!!

by iceinsidefire

Ha ha ha :)

That much interest in my posting??? ;)

Even my gf never read what I wrote with such interest. :(

Thanks and No sorry for mistake. :P
as you already corrected it.

This discussion is closed to new replies.