Question Locked

Blue Screen of Death!

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Along with my B.S.of D., I was supplied with the following Technical Information:
STOP: 0x00000024 (0x00190203; 0x82BD14C0; 0xC0000102; 0x00000000)
I contacted the relevant Microsoft site for an answer depicted by this code.
They came back with "code unknown".
Well, if they don't know, who does?
Any suggestions?
Edward Murphy.

10 replies

by nepenthe0

A Google search only turns up an advertisement for RegCure.

We need more information to assist you. What is your operating system? Did the BSOD appear upon attempting to boot? If not, what were you doing when Windows crashed?

Rick/Portland, OR

by jbaker

I was testing an image restore software called Paragon. I've created an image of a desktop. Then tried to restore the image on a different desktop. I think the problem is the software can not handle the differences in the hardware. The source hardware was a Dell Optiplex 170L. The new hardware is a Dell Optiplex GX260.

Who knew they were so different?

by bart777

This is usually caused by a problem with the disk or a corrupt ntfs.sys file.

If you can get into safe mode try running a
Chkdsk /f /r

If you can't get into the OS in any way then boot from the XP disk and get into the recovery console. Then run
Chkdsk /r

Hopefully this will get you back into the machine. If not you're looking at a new HD and possible loss of the data on that drive.

Sorry to pass on bad news...

Best of luck!

by robo_dev

Definition: STOP 0x00000024, 0X0000024, 0X24

Applies to: Windows XP and other operating systems.

This stop error means that your ntfs file system is corrupt (damage in the file system, bad hard drive data, corrupt SCSI or IDE drivers or a corrupt ntfs.sys file)

How to fix:
There are two ways:

1, If you still can access Windows, try to disable any backup programs, virus scanning programs or disk defragmenter tools. Try also to run a hardware diagnostics tool to detect any errors your hard drive might have. And run chkdsk /r to detect and repair any file system structural damage.

2, If you are unable to load Windows. Then you should try to access your ntfs partitions by making a ntfs boot disk with NTFS4DOS (freeware). You can download it from http://www.geekswhoknow.com/files/ntfsinst.exe You will need a floppy disk.

After you load the bootable floppy disk onto your damaged system, select either option one (1) or option three (3). If you selected option one (1), type chkdsk /r at the command prompt, and your problem should go away after the disk has been repaired.

Note! Unfortunately there is a chance that your partition is corrupt beyond repair and all of your data is lost. In that case, you need to reformat the partition to be able to use it again.

Additional information can be found at http://support.microsoft.com/default.aspx?scid=kb;en-us;Q228888

by nepenthe0

Will an attempt to reinstall the OS fail? Doesn't Windows run a version of [i]chkdsk.exe[/i] with recovery mode reinstallation?

Your response to Patrick's post is a model of clarity, which I have pasted into my .pdf archive for future reference. Too bad I can't give you another well deserved [i]thumbs up[/i]...

Rick/Portland, OR

by robo_dev

Sometimes the install will fail with a BSOD if there really is disk partition corruption (been there, done that).

by jbaker

In short... No Go.
I was hoping that this would correct this problem. I think the hardwareis just too dissimular for me to restore the image.

I hate to say this but I haven't had too must success with this Paragon Image software.

by Former member

A small memory dump or a big one. To test out put in your Xp or Vista disk and do a repair. Then after that, download a registry cleaner to remove any empty registry files or keys. I use Regcure:
http://www.regcure.com/lp/11/?uid=6vlb1
Of which does a very good job plus it does a restore point. But you will have to get the full version for this. Then when you have run this software you will find out if it does it again, but i doubt it. Delete all of your "temp files" also. Hope this helps you.

Please post back if you have any more problems or questions.

by rob miners

The problem you are having is to do with the Hardware Abstraction Layer or HAL. When you try and use the drive in a different PC it is trying to load the wrong drivers.

Because the PC's are physically different when it booted up the OS got really confused and started throwing errors. If you follow the advice in this link and disable Devices you should be good to to.

http://support.microsoft.com/default.aspx?scid=kb;en-us;824125

This discussion is closed to new replies.