Discussion Locked

Boot Issues

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Have a PC here that is giving me fits. This unit came back on warranty for a motherboard problem, which has been remedied. However, it now has boot problems which did not exist when it was sent out. Here's the issue: Windows 98 is installed on (somehow) a non-DOS partition. Initially, I could only get into Safe Mode. When I allowed the PC to boot normally, it would hang after the splash screen (black screen, blinking cursor). One time, let it boot normally and left the room, came back andOS was finding new hardware as a result of the motherboard replacement...but was sooooooooooooooooooo slow. Some dummy told me to FDISK with the MBR switch and now I am stuck. Any ideas on getting the MBR problem resloved? And how does Win98SE run on a non-DOS partition? Hard drive checks OK physically, and I can read the data when slaved on another machine.

12 replies

by maxwell edison

The non-dos partition was probably created when someone used a third-party disk-partitioning utility or installation program.

As far as the motherboard installation and the soooooooooo slow detection of new hardware devices, I would recommend that the operating system be reinstalled from scratch and, in your case, on a freshly partitioned and reformatted hard drive.

There are so many new devices detected with a motherboard installation, that the chances of Windows becoming unstable areincreased significantly. Since you could, at this point, retrieve the data from the drive, back up that data and start from scratch. The machine will run much better as a result.

Good luck,

Maxwell

by thomefan27

The obvious worst case solution is to reformat and reload, and my tech staff and I are aware that this is likely the avenue we will have to travel. However, I want to exhaust all other possible solutions first. Thank you for answering, though.

by thechas

Check out Microsoft Knowledge Base article Q186057.
It describes how to determine if a drive overlay program is installed.

If so, you will need to determine which program, and get the corect information on how to remove it.

Another possability is that the system was setup with the drive set to some other type than the autodetect on the new MB is choosing.

Since you can read the drive in another machine. Do you have enough space on another drive to backup this drive?

If so, copy thedrive into a folder.
Use a partition utility, if needed, to get the drive back to a normal state. (check out www.fdisk.fdisk.com for utilities and hints)
Format the drive from a W98 boot disk with the /s switch to copy the system files.
Copy thefiles back onto the drive.

You will still need to go through the hardware setup, but you will have recovered without having to load all the software.

by thomefan27

Microsoft's Knowledge Base article seems off the mark. The only thing I see that could possibly interfere is GoBack, which is installed, but I have disabled it. Already tried to reformat with a FAT32 partition and copy the files back to the drive,but upon reboot I experienced the original malfunction. When I brought up FDISK, the drive had changed from a FAT32 partion back to a non-DOS partition again. Thanks for trying, though.

by dmiles

Boot the system with a startup disk and at the command prompt type in SYS C:,or choose to boot system with out cd-rom support and let process reinstall the system files

Now check the blank screen by reinstalling the memory modules and the graphics card

by thomefan27

Soulrider, what I mean is the drive is not assigned a letter in FDISK, so I can't SYS to "C" because there is no "C".

by matsonic_dimm

Does It Get Through The Verifying DMI Pool Data
Does It Boot From Floppy Or Cdrom IF SO Then Try The Following:
Insert The Windows Cd 98 And Repair Windows This Will Not Install But Will Repair Anyway 98 Is The Best OS It Shouldnt Be Stuffing Up Since XP Came Out And If That Dont Work I Would Have A Very Good look In The BIOS Make Sure Your CMOS Battery Isnt Low It May Be Reseting Your Settings Disalowing The Pc To Boot Gatea20 Fast Boot Option And Try Getting In Command Prmpt By Inserting AFloppy And Trying To Get Into Safe Mode Via The Following c:\windows> win msconfig
and if it boots try to safeboot ok
another thing is try to get rid of the partion through a dos program like Par Magic Or Something Goodluck Bro

by thomefan27

You can't install Windows (or repair it) on a non-DOS partition. Already tried Partition Magic, no luck. Thanks.

by Member 32254067

all i would do is start from scratch.
1. boot into dos and load fdisk from a boot disk
2. from fdisk destroy all the partitions, dos and non dos
3. Format the drives accordingly making the fat or fat32 use (format /u) without parenthesis
4. Reload your OS and let the installation pick up the basic features on your motherboard.
5. once OS is loaded start installing the 2nd & 3rd party tools for your mother board and you should be ready to roll.
6. if the problem still persist at this poing then i would say you have some type of compatibility issue with hardware. Look into detail as far as perphiperal and other devices that may be conflicting with your OS.

by thomefan27

Have done this already. The only pieces of hardware in the mix at this point are the RAM, motherboard and hard drive, all of which have cheked OK using more than one third party diagnotics tool.

This discussion is closed to new replies.