Discussion Locked

Boot Issues v2.0 (Re-submitted)

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Same problem, but I will try to clarify the steps I have already taken to fix it this time before you decide whether to answer. (Thanks to TheChas, though...your answer was the only one that included something I hadn't already thought of.)

Customer sent a PC back on warranty and here is the problem: Installed a new motherboard and encountered boot difficulties. (Unit booted OK before it was sent to customer the first time.) Boots to Safe Mode OK, but normal boot hangs after splash screen(black screen with blinking cursor). Normal boot was partially successful ONCE, but hung when installing new motherboard devices. Found that Windows 98SE is somehow installed on a non-DOS partition.

1.Attempted to convert the partition to FAT32using Partition Magic, to no avail.
2.Scanned for viruses twice, no viruses found. 3.Manually set drive parameters in BIOS.
4.Attempted to SYS the drive from a boot floppy, but cannot do it on a non-DOS partition because there is no drive letter assigned.
5.Tried reloading OS, but cannot do it on a non-DOS partition (which begs the question as to how it is even installed in the first place)
6.Copied drive contents to another machine, reformatted the drive with a new FAT32 partition and copied the contents back over. Same malfunction persisted, and when I ran FDISK, the partition had been changed back to non-DOS again.

There are no add-in components currently installed. Only motherboard, RAM and hard drive, all of which have tested OK using more than one third party diagnostics tool. The idea is to resolve this problem without having to reinstall all of the applications.

20 replies

by md_hashim

Whats the hardware thats being used? Have any jumper seetings been changed? It may be a good idea to check that. Check the power supply to the hard drive etc.

by thechas

If you can still boot into safe mode, I would do the following:
Note: registry edits can disable the system. Proceed with caution.

1. Clear everything from the programs\startup folder. you want to prevent any software from getting in your way.
2. Use sysedit, or msconfig, and clear out any hardware settings in autexec, config, win and sys files.
Rem out any unfamilier software.

3. Open regedit.
Search the run, runonce, and runonce except keys for any "unusual" programs.
Then search the hardware and drivers section for devices that no longer exist, delete the keys.
(I might even remove all hardware device keys, and let windows re-install everything)
Look through the runservices sections to see if there is anything "unusual" there.

4. I haven't tried it from safe mode, but SFC (system file checker) may provide a clue also.

Beyond the above, I would try the copy, format, copy routine again. But instead of booting up to the hard drive, boot to a W98 startup disk, and re-install Windows.
You won't loose the installed software, only a few updates, such as IE.

Best wishes, Chas

by thechas

Remembered seeing the following in another Question.

It may help with cleaning out the old hardware settings.

What he did was remove the enum key under hkey_local_machine. Without getting real complicated, it's basically where windows will store all the information that it loads about your hardware.

Chas

by mdelyea

If you can boot to safe mode then half the battle is over. Unplug the CDROM and plug a FAT32 hard drive (with enough room to copy all the files) into the secondary master. Start in safe mode. Start Windows Explorer. Make sure 'show all files' isenabled in folder options. Go to a Command Prompt and type 'xcopy32 c:\*.* /e /c'. Some files may not be copied if they are in use at the time but you should get about 99% of the drive. When finished, shut down and remove the old drive and install the drive you copied everything onto as primary master and plug the CDROM back in. Boot with a boot floppy and go to c:\windows and rename win.com oldwin.com (or something similar). Change to the setup folder (win9x on the CD or hard drive) and run setup. When prompted for the install folder (setup will suggest windows.000) select c:\windows instead. This will preserve the software and settings from the old installation. This should work.

by thomefan27

That did the trick. (At least the part about editing win.com and installing to the existing Windows directory, anyway.) Wow, what a hassle. The OS is still a little unstable, but as long as that partition problem is rectified I am satisfied. Thanks a lot for your assistance.

by timthetoolman

Hi,

Just to add to TheChas' suggestion of "removing unusual programs", here is a quote from a Seagate technician on this subject...

"The non-DOS partition is most likely due to a Dynamic Drive Overlay being installed on the drive (like Disk Manager or EZ Drive). Try running a low level format on the drive."

The complete article came from...

http://forum.seagate.com/SERVICE/Email%20Forum.nsf/8c41ab42beba508d88256977005b9901/699897cfee653d62862569c4007a12a3?OpenDocument

(remove spaces from the above URL)

Which describes it in more detail.

Cheers,
Tim.

by shanghai sam

Downloaded and ran Seagate's DiscWizard utility. Same problem persisted. It seems that the cause of the malfunction lies in the original contents of the drive and not in the drive itself. Thanks for trying. I was optimistic about that one.

by hjs

I agree with #5. I have seen this before. First thing I would do is run fdisk/mbr just to get rid of any crap in the master boot record. Boot into safe mode and blow away the video card. Reboot into normal mode and it should find new hardware and ask for the drivers. If it asks if you want to keep the old drivers answer no. Good luck.

by thomefan27

Wiped out the MBR yesterday and doubled my frustrations. Not sure what your intentions were on the video card theory, but thanks for trying.

by timthetoolman

Hi,

I think that when you reload the system back on after the format, you'll be reloading the Disk Manager software (or whichever one it is) back on with it.

I'm not exactly sure how Disk Manager works, but I suspect it gets started very earlyon in the boot.

The way to check this would be to re-format your drive (as you've now done a couple of times !) and then boot to DOS using a floppy and run FDISK.

If it shows as being FAT32, then you can be reasonably sure that there is some sort of Drive Overlay thing happening.

How do you remove it? I'm not sure about that one... I've never used the software. Certainly installing windows afresh would do it, but I know you want to avoid that as you dont want to reload all the applications. If you look into Disk manager, you may come across a removal method!?

If you cant find it and no-one else gives you a solution, then I guess re-installing will be your only course of action, though.

Cheers,
Tim.

by thomefan27

I ran a low-level format using the Seagate utility that I downloaded, so maybe that helped in conjunction with suggestion #5. I do know that it alone did not fix the problem. Thanks for your help...it feels so bad having to rate some of these answers "Rejected". Sorry.

by thomefan27

Thanks to all who tried to help me on this very frustrating issue. I feel bad having to rate good answers "Rejected", but hopefully you understand.

This discussion is closed to new replies.