Discussion Locked

Boot Problem

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
PC will not boot from HD or Floopy. New Tyan S1598 MB, 64meg Memory(kingston) recommend by MB manufacturer. New Intel 233MMX processor. Also new ATX case with 250W power supply. HD previously used in with 486 CPU. No problems. Have tried booting with bare essentials of video card. Intial boot sees floopy, memory of 64 megs, CD-ROM drive. Thoughts, comments suggestions will greatly appreciated. Beating head against PC for two weeks.

15 replies

by fdisk

Remember black to black on power and the red stripe on all IDE and floppy cables always have pin one on the controler and next to power on the drive. The best way to test this is disconect every thing including all drives. If you can get to bios at that point it will boot if the bios is configured right. I nothing comes on at this time romeve any one of the following (CPU,RAM or video) and plug in the pc speaker.
If you hear a sound patern when power is aplied that device component that wasremoved is good. If no sound can be heard the main board may be dead.

by dmiles

Go back over your cable connections and make sure that all cables are connected and seated correctly
Check the memory seating to insure that memory is seated correctly in correct banks.
Does the HD spin when you boot the computer up.
It sounds asthough you have the cable connections turned around follow the suggestions in ans.1

by rthompson

Along with making sure Cables are seated and to pin 1 settings, the other advantage of having the PC speaker plugged in is getting the error code sequence to follow up on. Refering to BIOS error code desriptions in a Tech. Reference can lead you inthe right direction. If your seeing Memory test readings on screen etc. your getting by system power on test, so your power connections are O.K.

Good Luck,
R.T.

by otl

Initial boot sees floppy but will not boot? Bad disk/floppy/cable. Remember new cables are not always good. Swap with known good and ensure connections are correct, which they appear to be.

Bare essentials, do you mean floppy/video? No memory/HD/CD? Memory/HD controller/CD controller? That would be bare essentials. If it does not boot then it is MB/Processor/Floppy controller, otherwise keep adding until it fails.

Make sure BIOS is set correctly for the old HD or autodetect. Normally settings for HD are on the HD.

by bryan_hartman

Go into your bios settings and make sure that your primary hard drive is set to auto detect. If the mother board is not capable of auto detecting you might have to put the sttings in manually(settings normally listed on the hard drive) You will probably want to check the boot order also. Set it to boot to the floppy(A drive) before the hard drive so you can boot off the floppy if you would like to.

by cajundon

Hi, I see one suggestion that has not been mention before in other post.

Do you have the Hard Drive and CDROM connected to the Primary IDE Channel? If you do, switch the CDROM to the Secondary IDE Channel and change the jumper to Master on the CDROM. You can have conflict with the Hard Drive and CDROM with them being on the same IDE Channel, but mostly it slows down the speed of Hard Drive.

If you install a Zip Drive or any other IDE device, connect it to the Secondary IDE Channel, and you can set either one as the Master Device and the other as the Slave Device. It is best to install only Hard Drives to the Primary IDE Channel for best performance. Also have the BIOS Auto Detect all devices.

Good luck and have a great day.

DonThibodaux, Computer Technology Consultant.

by burtsa

Perhaps I am not understanding you but what I am gathering here is that everything is starting up fine you just can't boot.

First thing I would check is to make sure that your boot order in bios is A:,C:

Then I would, if you still can, find out what the settings were that you used on that 486. The drive may need to be configed that way to see the existing partition.

Shawn

This discussion is closed to new replies.